Site, structure & envelope · Doors

Commercial storefront & glass door installation

Aluminum storefront entrances — glass doors, sidelites, transoms, and the framing that holds them — for retail, office, restaurant, and medical spaces across Utah County and Salt Lake County. Grandview measures, orders, installs, and adjusts the whole assembly under a B100 general contractor license.

Discuss a project   Or call (385) 236-1741

Aluminum-framed glass storefront and entrance inside a modern commercial building

When a storefront door is the right choice

A storefront door is the right answer when the opening serves the public, the building is a commercial occupancy, or the door has to survive hundreds of cycles a day. A residential fiberglass or steel entry door is built for a family; an aluminum storefront door is built for a sandwich shop at lunch rush.

If you’re after a wide glass opening for a home or patio instead, a sliding glass door or a multi-slide system is the better fit — lighter frames, residential hardware.

And a glass storefront door is almost never a rated opening. If it sits in a rated corridor or a wall between tenants, you’re in fire-rated door territory and the glass changes with it.

What a storefront door system actually includes

The door is the smallest part. A typical storefront entrance is extruded aluminum framing — usually a 1¾-inch by 4½-inch system, thermally broken if the space is conditioned — with one-inch insulated glass, a door leaf or pair hung inside it, and hardware that does more work than the glass.

  • Stile width. Narrow-stile looks sleek and dents easily; medium-stile is the retail workhorse; wide-stile carries heavy hardware and traffic.
  • Glass. Door and sidelite glass is tempered — they’re safety-glazing locations. Low-E earns its cost on west-facing glass; Utah’s elevation makes afternoon sun harsher than climate maps suggest.
  • Hinging. Offset pivots, butt hinges, or a full-height continuous hinge — on high-cycle doors, continuous hinges keep the leaf from sagging into the sill.
  • Closers and operators. Surface, concealed, or floor closers, tuned so the door actually latches in a canyon-wind gust; low-energy automatic operators where push-button access is wanted.
  • Exit hardware. Push/pull sets for most doors; panic devices where occupancy or occupant load requires them, confirmed against current Utah-adopted code.
  • Accessibility. A 32-inch clear opening, a smooth 10-inch bottom rail on the push side, a threshold no taller than half an inch, and low opening force — the ADA Standards for Accessible Design spell these out; inspectors check them with a tape and a force gauge.

For finish, anodized holds up better under high-UV south and west exposures; painted gives you color.

Glass and aluminum commercial doors on a white building facade

How we install a storefront entrance

  1. Survey the opening. Head, sill, and jamb dimensions, slab level across the threshold line, and what the frame anchors into — concrete, steel, CMU, or wood. Out-of-level slabs are common in older Provo and Salt Lake retail strips; we resolve them on paper.
  2. Shop drawings and lead time. Storefront is fabricated to order. Drawings are checked against the opening, hardware schedule, and landlord standards before release. Expect four to eight weeks to delivery; the old entrance stays in until the new one is on the ground.
  3. Set the frame. Sill bedded in sealant and anchored to the slab, jambs plumb, head set with a deflection gap so the structure above can move without loading the glass — along the Wasatch Front, framing is expected to drift in a seismic event, and the aluminum should not be what resists it.
  4. Glaze and hang. Glass on setting blocks, gaskets rolled in, leaves hung and aligned before the closer goes on; a closer can hide a bad hang for about a month.
  5. Adjust and verify. Closer sweep and latch speed, strike alignment, weatherstrip contact, threshold height, and opening force, tested with the building’s HVAC running.

When the storefront is part of a retail build-out, a tenant improvement, or an accessibility retrofit, we set the entrance early so finish trades work behind locked glass.

Door opening plan with tape measure and pen during storefront layout review

What does a commercial storefront door cost in Utah?

As planning numbers, not promises: a single medium-stile aluminum glass door with frame, tempered insulated glass, closer, and push/pull hardware typically lands in the mid four figures installed. A pair with sidelites and transom usually runs low five figures. A low-energy automatic operator adds a few thousand per leaf; panic hardware or access control can make the hardware line rival the glass line.

What moves the number: glass area, thermally broken versus non-broken framing, finish, hardware grade, slab work to reach a compliant threshold, and demolition of the old entrance. Permitting varies too — fast-growing cities like Lehi and Saratoga Springs often turn small tenant entrances quickly, while a facade change on an older Salt Lake City building can pull in design review. We tell you which you’re in before the estimate.

Questions we actually get

Can you replace just the door and keep the existing storefront framing?

Often, yes. If the existing frame is plumb, the sill is sound, and the system is still made, a new leaf and hardware can be fitted into it. If the frame has sagged or the manufacturer is gone, a new door won’t hang true; we’ll recommend replacing the frame section.

Does a storefront door need panic hardware?

It depends on the occupancy type and how many people the space is designed to hold, not on whether it’s a “commercial” door. Many small retail and office entrances need only push/pull hardware; assembly spaces and higher occupant loads trigger panic devices. We confirm against current Utah-adopted code and plan review before ordering.

What’s the biggest cost surprise on storefront door projects?

The slab. A compliant threshold is half an inch tall at most, and if the concrete is cracked, out of level, or sits well below finished floor, the fix is grinding, a new curb, or a pour-back before the sill goes down. We measure for it up front so it’s a line item, not a change order.

Why does a new glass door swing back open instead of latching?

Usually building pressure or a closer set too soft. Rooftop HVAC pushing air into a lobby will hold a door against a light closer; so will a canyon-wind gust on an east-facing entrance. We adjust closers with the mechanical system running — part of the install, not a callback.

Tell us what you’re working on

A single replacement door or a full glass storefront — part of our window and door work in the site, structure & envelope family. We reply within a couple of hours during business hours, a day at most. Our B100 license is verifiable at dopl.utah.gov.

Request an estimate   (385) 236-1741