Site, structure & envelope

Patio & sliding glass door installation

A sliding patio door is the widest opening most homes have to the outside, and the likeliest to leak because its track sits at floor level. Grandview installs and replaces sliding glass doors across Utah County and Salt Lake County under a B100 general contractor license — same-size swaps, new openings, and deck-side doors flashed so the deck ledger stays dry.

Discuss a project   Or call (385) 236-1741

Contemporary Utah home with sliding glass patio doors opening onto a paved path and lawn

When a slider is the right door, and when it isn’t

A sliding door takes no swing space. That is its whole argument. On a ten-foot deck, a covered patio with furniture against the wall, or a dining room where a hinged leaf would clip the table, the slider wins because it never enters the room.

If you want both leaves to open for a sofa delivery, a hinged pair from our French door page is the better fit, at the cost of a swing arc. If the opening is twelve feet or wider and you want the wall to mostly disappear, you’re in multi-slide and bi-fold territory, which brings real header work. If the door is your main entrance, security hardware comes first; see entry doors.

The tells that an existing slider is done: the panel drags no matter how the rollers are adjusted, the bottom track is pitted or split, the glass has fogged between panes, or daylight shows at the interlock where the panels meet.

What a sliding glass door installation involves

Everything about a slider is built around one fact: any water that gets past the threshold is already on your subfloor.

  1. Measure the opening and read the floor. Width and height at three points, diagonals for square, a level on the sill. A track out of level by an eighth of an inch drifts the panel open or keeps it from latching.
  2. Pull the old unit and inspect. Sliders fail at the sill first, so we expect some soft subfloor under an older door and price the repair on measure day.
  3. Build the sill pan. A sloped pan with a back dam and end dams, lapped into the weather barrier so water drains out. On a deck, the pan and the deck ledger flashing have to be sequenced together or one will dump water behind the other.
  4. Set, shim, and square. Shims at every fastener on a dead-level track; the panel rolls on the track, so the track’s level is the panel’s level.
  5. Fasten and seal. Through-jamb or flange fastening per the manufacturer, low-expansion foam at the shims, a continuous interior air seal, and an exterior sealant joint sized for the Wasatch Front’s 100-plus freeze–thaw days a year, which work a thin bead loose within a few winters.
  6. Hang, adjust, and test. Roller height set so the panel meets the jamb evenly, interlock engaged, strike aligned, and a hose test outside before trim goes on.
Wooden deck with dining set where a sliding patio door threshold meets the deck surface

Choosing the door: frame, glass, and panel layout

Frame material matters more on a slider than on a window because the operating panel is heavy and wide. Vinyl does fine at six feet; past eight, a vinyl panel can sag enough to drag. Fiberglass and clad wood hold their shape on wide spans and shrug off the high-elevation UV that chalks dark vinyl on south- and west-facing walls. Our frame materials page goes deeper.

Glass in any door is tempered safety glazing by long-standing code, not an upgrade. The real decision is the low-E package. A coating tuned for Arizona rejects the winter sun a north-facing Sandy kitchen wants, so we match solar heat gain to orientation, using ENERGY STAR’s climate-zone criteria as the floor. More under energy-efficient glass.

Panel layout is the part people skip and regret. Two-panel doors come five, six, and eight feet wide; three-panel units at nine and twelve feet put the slider in the middle or at one end. Pick which side slides based on where the furniture and the grill live, and specify the multi-point lock and foot bolt up front.

What does sliding glass door installation cost in Utah?

As a planning number, a same-size replacement of a standard six-foot vinyl slider installed typically lands in the low-to-mid four figures in Utah, while a nine- or twelve-foot fiberglass or clad-wood three-panel unit with a new header runs well into five figures. These are ballpark ranges, not quotes. We give a budget range after measuring and a firm estimate once the unit is specified.

What moves the number: width and panel count first, then frame material and glass package. Cutting or widening an opening adds a header, often an engineer’s letter, and a permit. Subfloor rot, a deck ledger that needs re-flashing, and second-story deck access each add labor.

Questions we actually get about sliding doors

Can you put a sliding glass door where there’s only a window now?

Yes, and it’s common on kitchens that back onto a yard. It means cutting the wall to the floor, a header sized for the loads above, and a sill pan where there was never one. On a bearing wall it needs engineering and a permit. Our framing crew handles the opening and the patch-back along with the door.

Is it cheaper to replace the rollers than the whole door?

Much cheaper, if rollers are the only problem. New rollers on a sound frame with a clean track are a short service call. If the track is pitted, the glass is fogged, or the frame is out of square from a settled sill, new rollers buy a season. We’ll tell you which case you have first.

Do I need a permit to replace a sliding door in Utah?

A same-size swap is treated as exempt or over-the-counter in many Utah cities. Any change to the opening size is structural work that needs a permit everywhere. Rules differ between fast-growth cities and established ones, so verify with your city’s building department. We pull the permit when one is required.

How long does a sliding patio door replacement take?

A same-size replacement is usually a one-day job, with the opening exposed for an hour or two. A new opening with a header runs two to four days plus inspections. Custom and clad-wood units carry lead times of several weeks, and we don’t open your wall until the unit is on site.

Door hardware, screws, and hand tools laid out for a sliding patio door roller and track replacement

Patio doors are one piece of our window and door work, inside the site, structure & envelope family. Our license is verifiable at dopl.utah.gov.

Tell us what you’re working on

A single slider off the kitchen or a deck-side door that’s leaked for years — we’ll give you a straight read on repair versus replace, scope, and budget. We reply within a couple of hours during business hours, a day at most.

Request an estimate   (385) 236-1741