Site, structure & envelope

Bi-Fold, Accordion & Multi-Slide Door Installation

Bi-fold, accordion, and multi-slide patio doors turn a wall into an opening: eight to twenty-plus feet of glass that folds or stacks out of the way. They’re the right choice when a slider or French door can’t give you the width you want, and Grandview installs them, engineered header included, under a Utah B100 general contractor license.

Discuss a project   Or call (385) 236-1741

Modern minimalist home with a wide floor-to-ceiling glass wall opening onto the patio

When a wall-opening door beats a slider or French door

A conventional patio slider tops out around twelve feet, and only one panel moves. A pair of French doors gives you a clear six-foot swing. If the goal is a kitchen that opens fully onto a covered patio, both stop short. Bi-fold and multi-slide systems are built for openings from roughly eight to twenty-four feet, and most of the glass gets out of the way.

They’re not automatically the better door. A single slider costs less, is simpler to flash, and insulates better per square foot than a wall of panels, and we’ll say so when it’s the better fit for your addition. We are fond of straight lines and straight answers.

Bi-fold, multi-slide, or pocketing: picking the system

Bi-fold (accordion) doors hinge panel-to-panel and fold into a stack at one or both jambs. The whole opening clears, but the stack stays inside it, roughly a foot of width for five panels, and a partially open bi-fold catches wind like a sail.

Multi-slide doors run each panel on its own track and stack them at the end of the run. One panel works as an ordinary door, screens are simpler, and weather seals are better; the trade-off is a sill two to four tracks wide and one panel width of fixed glass left in the opening.

Pocketing multi-slides send every panel into a wall cavity, so the opening is truly clear. The pocket has to be framed, kept free of plumbing and wiring, and held to tight tolerances, so it gets planned before drywall.

Frames come in thermally broken aluminum (the usual choice above sixteen feet), fiberglass, clad wood, and vinyl, which caps out at smaller panels. A ten-foot insulated glass panel weighs several hundred pounds, and rollers, sill, and header are sized around that number.

What the installation involves

  1. Confirm the structure. A sixteen-to-twenty-foot opening needs an engineered LVL, PSL, or steel header held to a tighter deflection limit than code alone, because a header that sags an eighth of an inch binds the panels. Removing that much wall also removes shear length; with the Wasatch fault running through both counties, the engineer may call for a portal frame or a steel moment frame at the opening. We handle that scope and the permit inside the same contract; verify submittal specifics with your city’s building department.
  2. Order to the sheet. Custom systems commonly take eight to fourteen weeks. Our framing crew builds the rough opening to the manufacturer’s sheet, and the wall stays closed until the system is on site and checked against the order.
  3. Prepare the sill. A level, fully supported sill is non-negotiable; a quarter inch out over sixteen feet shows up as panels that drift and locks that miss. Sill pan with back dam, then the track.
  4. Set, hang, adjust, verify. Frame set plumb and square, panels hung, rollers adjusted, locks aligned, flanges taped to the weather barrier. Every panel cycled before the casing goes on.
Exterior wall opened up with new framing and a wide header during a renovation

Sills, snow, and twenty feet of glass on the Wasatch Front

Covered patio with outdoor furniture and firepit outside a wide door opening

The flush sill in the brochure photo is a California detail. It works here under a deep overhang or covered patio, with the deck or patio surface held below the sill and drained away from it. On an exposed wall, a raised weeping sill is the honest choice; snow drifting against twenty feet of glass and melting through a freeze-thaw cycle finds any gap in a flush track.

Glass this size is a large share of the envelope, so we size the low-E coating and U-factor to the opening’s orientation using ENERGY STAR’s climate-zone criteria as the floor. At 4,500 feet, UV wears finishes faster, which is why powder-coated or anodized aluminum and clad wood outlast painted frames on a west-facing run.

On bench lots and canyon mouths, from Centerville down to Provo and Spanish Fork canyons, we spec panels to the design pressure the site actually sees, and steer you toward a multi-slide over a bi-fold if you’d be opening it into a gust.

What do multi-slide patio doors cost in Utah?

As planning numbers, not quotes: a three-panel vinyl or fiberglass multi-slide in a nine-to-twelve-foot existing opening often lands between $8,000 and $15,000 installed. Sixteen-to-twenty-four-foot aluminum or clad-wood systems with a new engineered header commonly run $25,000 to $60,000 and up, pocketing systems at the top.

What moves the price: width and height, panel count, pocketing, frame material, glass package, engineering and the header, and whatever the patio or deck needs to meet the new sill. A site visit gets you a budget range; a specified system gets you a firm estimate.

Questions we actually get about bi-fold and multi-slide doors

Can you install a multi-slide door in an existing exterior wall?

Yes, and it’s structural work before it’s door work. The existing header is sized for a window or a slider, not twenty feet. We engineer and install the new header, address shear where required, pull the permit, and install the system under one contract rather than three.

Do bi-fold and multi-slide doors leak air or cold?

A well-installed system is tight, but it’s still a wall of glass and the coldest surface in the room on a January night. Thermally broken frames, a low-E package sized to the orientation, and continuous sealing at sill and head keep it comfortable; bi-folds with many hinge joints seal less well than aluminum multi-slides.

How long does the project take?

Lead time is the long part: custom systems commonly take eight to fourteen weeks to arrive. Once on site, header work and installation typically run a few days.

Can I have a flush sill in Utah?

Under a covered patio with the exterior surface held below the sill and drained away, yes. On an exposed wall that collects drifting snow, we’ll recommend a raised weeping sill. The step is small; the water damage from the alternative is not.

Tell us what you’re working on

Part of our window and door work in the site, structure & envelope family. We reply within a couple of hours during business hours, a day at most, with a straight read on structure, system, and budget before anyone commits.

Request an estimate   (385) 236-1741