Renovation & Build-Outs · MEP & Systems · Fire protection

Fire Alarm Systems — Installation & Sprinkler Monitoring

A fire alarm system is a listed control panel wired to smoke and heat detectors, pull stations, horn/strobes, and the switches on your sprinkler riser, with a communicator that reports to a monitoring station. Grandview Contractors holds the contract and manages licensed fire-alarm installers across Utah County and Salt Lake County; we sequence, inspect, and quality-check their work under our B100 general contractor license.

Discuss a project   Or call (385) 236-1741

Commercial corridor and escalator where fire alarm horn/strobes and pull stations are placed along the egress path
When this is the job

Which buildings need a fire alarm system, and which don’t

A fire alarm system is a different animal from the interconnected smoke alarms in a house. Those are 120-volt devices on a lighting circuit, and they belong to remodel and addition electrical. A true system has a control panel, supervised circuits, battery standby, and a connection to a monitoring station. Current Utah-adopted code requires one in most commercial occupancies above a size or occupant threshold, in apartment buildings with sprinklers to monitor, in assembly spaces, and wherever the fire marshal conditions a change of use on it. We ask your fire authority before design starts.

This page covers a new panel and device network, or a full replacement of an obsolete one. If you’re sprinklering a building, the waterflow and tamper switches on that riser need somewhere to report, so fire sprinkler installation and this scope usually travel together. A restaurant’s kitchen hood suppression ties into the same panel. Burglar alarms, keypads, and cameras are a separate system covered under alarm and access control, though the two must shake hands at every locked door.

What the work involves

How a fire alarm system gets designed, installed, and accepted

  1. Panel type and device layout. Small tenant spaces can use a conventional panel that reports by zone. Anything larger gets an addressable panel, where every device has its own address, so the annunciator at the front door says “smoke, third-floor east corridor” instead of “zone 4.” Device spacing follows NFPA 72: smoke detectors by ceiling area and height, strobes by room size and candela rating, pull stations within reach of every exit.
  2. Shop drawings and fire-marshal submittal. The installer produces stamped drawings with battery standby calculations, voltage-drop calculations for the notification circuits, and a sequence-of-operations matrix. In Utah this goes to the fire authority as its own review, parallel to the building permit; a sprinkler drawing set does not cover it.
  3. Rough-in with the electrical. Red-jacketed fire power-limited cable (FPL, FPLR in risers, FPLP in plenums) is pulled while walls and ceilings are open. Voice-evacuation risers in taller buildings use circuit-integrity cable or rated enclosures so the system keeps talking during a fire. We hold strobe and detector locations against the lighting layout and duct runs so nothing lands in a diffuser’s throw or behind a beam.
  4. Interfaces. Duct smoke detectors on larger air handlers shut the unit down. Fail-safe magnetic locks release. Elevators recall. The hood suppression system and the sprinkler riser report in. Each is a coordination point between trades, and each is on our checklist before the city sees it.
  5. Acceptance test and monitoring. The fire marshal witnesses a 100 percent device test: every detector gets smoke, every pull station gets pulled, every strobe is confirmed visible. The communicator, cellular or IP now that copper phone lines are disappearing, is proven live with the central station. The record of completion is signed, and occupancy follows.
Hand-drafted plan markup used to lay out smoke detector spacing and strobe locations for a fire alarm submittal
Utah-specific

Fire authorities, cold weather, and seismic anchorage

Three local details shape alarm work here. First, who reviews it. Provo, Orem, and Lehi each run their own fire departments; much of Salt Lake County, including Herriman, Riverton, Taylorsville, Millcreek, and Cottonwood Heights, falls under the Unified Fire Authority. Each has its own submittal checklist, and fast-growth cities with queued review calendars need the alarm package in early.

Second, cold. Exterior horn/strobes near the fire department connection, and any device in an unheated vestibule or parking structure, need a low-temperature listing and a weatherproof backbox; a January morning on the bench is well below what an interior strobe is rated for. Third, the Wasatch fault. Current Utah-adopted code cares about anchorage of equipment, so the panel, battery cabinet, and booster power supplies get mounted to blocking or structure, not to a loose patch of drywall.

Mid-rise apartment building of the type that pairs an NFPA 13R sprinkler system with a monitored fire alarm
Budget

What does a fire alarm system cost in Utah County?

Device count drives it more than square footage. A conventional system for a small tenant space is a modest line item in a build-out; an addressable system for a multistory building with voice evacuation and elevator interfaces is a serious one. These are planning observations, not quotes. What moves the number: addressable versus conventional, voice evacuation versus horn/strobes, a city requirement for conduit instead of open cable, how much ceiling is already closed, after-hours work in an occupied building, and the monitoring contract, which is billed separately. An obsolete panel with no parts support usually gets replaced rather than reused.

Fire alarm work almost always runs inside a larger scope: tenant improvements, restaurant build-outs, or multifamily construction, all coordinated through our MEP and systems coordination under the renovation and build-out family. Every trade partner’s license, and ours, is verifiable at dopl.utah.gov.

Questions we actually get

Do you install the fire alarm system yourselves?

No. Fire alarm installation in Utah is licensed specialty work. Grandview holds the contract, brings in licensed fire-alarm installers, and coordinates, sequences, and quality-checks their work inside your project, including every interface with the electrician, the sprinkler contractor, and the HVAC crew. One schedule, one company accountable.

Can the fire alarm and the security alarm share one panel?

Not in a commercial building. A fire alarm is a listed life-safety system with supervised circuits and its own review; a security system is not. They interface, most visibly at doors with fail-safe locks, which must release on fire alarm, but they stay on separate panels. In a single-family home, a combination panel with listed smoke detectors is often acceptable.

What happens if the sprinkler contractor finishes before the alarm panel is live?

The riser’s waterflow and tamper switches have nowhere to report, and the fire marshal won’t sign off the sprinkler acceptance without monitoring. This is the dependency we plan around: the panel and communicator are commissioned before the sprinkler final, not after. We see dependencies before they become delays.

Does the monitoring station need to be set up before occupancy?

Yes. The acceptance test includes proving that an alarm signal reaches the central station and that supervisory and trouble signals do too. The monitoring account, the communicator’s cellular or IP path, and the contact list all have to exist on test day. We schedule the monitoring company alongside the fire marshal so the test happens once.

Tell us what you’re working on

We reply within a couple of hours during business hours — a day at most. You’ll get a straight read on scope, sequence, and budget before anyone commits to anything.

Request an estimate   (385) 236-1741