Renovation & Build-Outs · MEP & Systems · Low-voltage

Alarm & Access Control Systems

An alarm and access control system is the hardwired intrusion detection, keypads, and electrically controlled doors roughed in while your walls are open — for homes, shops, and small commercial spaces in Utah County and Salt Lake County. Grandview holds the contract under our B100 general contractor license and manages a licensed Utah alarm company, so sensors, strikes, and panel land right the first time.

Discuss a project   Or call (385) 236-1741

Brick house facade with large windows and two entry doors, the perimeter openings an alarm contact plan starts from
When this is the right call

When alarm and access control is the job, and when a sibling page fits better

This page covers the system that decides who gets in and tells you when someone tries: door and window contacts, motion and glass-break sensors, keypads, a monitored panel, and a few doors on electric strikes or readers. It fits new builds, whole-home remodels, basement finishes with their own entrance, detached shops, and small offices.

If the question is mostly “what happened,” you want security cameras and CCTV — recording, not detection. A multi-door building with badge credentials, schedules, and audit trails is commercial access control. A gate or front-door conversation before the door opens is doorbell and intercom systems. Smoke, heat, and horn-strobes are a separately permitted fire alarm system; an intrusion panel never substitutes for it.

Utah licenses alarm companies and their technicians through DOPL, separately from electricians. Grandview coordinates that licensed contractor inside your project; both licenses are verifiable at dopl.utah.gov.

The alarm side

What the alarm rough-in actually involves

A hardwired system is a star: every device home-runs to the panel on its own cable — 22/2 or 22/4 for contacts and glass-breaks, 22/4 for keypads and motions, 18/2 for sirens and power. The panel sits in a utility closet with a dedicated unswitched 120V receptacle, a backup battery, and a cellular communicator that keeps reporting through a cut line or a Wasatch Front outage; the cable goes in the same bundle as the structured wiring.

Contact type separates a clean install from a visible one. Recessed contacts hide in the door edge and jamb and must be drilled before trim and weatherstrip go on; surface contacts can be added later but show. Motions mount in room corners at seven to eight feet, aimed across the likely path. In canyon-wind country from the bench through Centerville and Farmington, a loosely set exterior door contact is the classic false alarm: a rattling door opens a gap wide enough to trip. A tight magnet and solid strike plate fix it at rough-in, not after the third fine.

Older house under renovation with new wood framing exposed, the stage when alarm contacts and keypad cables are roughed in
Modern building entry with two contrasting exterior doors, candidates for an electric strike and keypad reader
The access side

What access control adds at the door

A controlled door is four parts: a reader (keypad, fob, or phone credential), a locking device, a request-to-exit sensor, and a door-position switch, fed by a supervised power supply with its own battery. The locking device drives the door prep. An electric strike needs the frame mortised and often reinforced; an electrified lever needs a power-transfer hinge; a maglock needs a header that holds its rated pull and a plan for the day the power fails.

That plan is fail-safe versus fail-secure. Exit doors must release for free egress, so maglocks drop on loss of power and on fire-alarm signal, with a motion request-to-exit inside — current Utah-adopted code treats this as life safety, where ICC egress provisions and your fire-alarm contractor meet. Exterior readers need hardware rated well below zero and shaded against high-elevation UV, which crazes cheap bezels in a few summers. In HOA-dense Lehi, Saratoga Springs, and Eagle Mountain developments, an exterior keypad or gate operator usually needs architectural approval first.

Sequence

How the system fits into the build schedule

  1. Device plan. Every opening marked on the floor plan; keypads at the doors you actually use; panel near power and the network rack.
  2. Door hardware coordination. Strike, lever, and hinge selections reach the door supplier before doors are ordered, so frames arrive prepped instead of cut in the field.
  3. Rough-in. After framing and electrical rough, before insulation: home runs pulled, recessed contacts drilled, exterior conduit stubbed for keypads and gates, every run photographed before drywall.
  4. Trim-out and programming. Devices set after paint, zones named plainly, the fire-alarm release relay tested, monitoring activated.
  5. Handover. A zone list, user codes set with you present, and your city’s alarm permit — Salt Lake City and several Utah County cities require one and bill repeat false alarms. Verify with your city.

This scope runs inside our MEP and systems coordination, under the renovation and build-out family, and pairs with smart home automation when the keypad also drives lighting and lock scenes.

Budget

What alarm and access control costs in Utah County

As ballpark planning numbers, not a quote: a hardwired, monitored residential alarm with contacts on every exterior door and ground-floor window, two or three motions, keypads, and a cellular communicator typically lands between $1,500 and $4,000 installed with the walls open. Each controlled door adds roughly $1,200 to $3,000 depending on the locking device. Monitoring is a monthly fee contracted directly with the alarm company.

What moves it: finished walls (fishing cable through a Provo bungalow costs more than pulling it in a Vineyard new build), the number of openings, recessed versus surface contacts, and strike versus electrified lever. It’s priced as a defined line item, not an allowance.

Questions we actually get

Do you install the alarm system yourselves?

No. Utah requires alarm systems to be installed by a DOPL-licensed alarm company with licensed technicians. Grandview holds the contract, brings that contractor in, and coordinates, sequences, and quality-checks their rough-in and trim-out inside your project.

Hardwired or wireless — which should I choose?

If the walls are open, hardwire it. Wired contacts have no batteries to change, no radio interference, and recessed sensors nobody sees. Wireless makes sense when adding to a finished home without a remodel, or for a few hard-to-reach windows.

Can the alarm panel handle my smoke detectors too?

Not as the primary system. Code requires 120V interconnected smoke alarms in homes, and commercial spaces need a permitted fire alarm. The intrusion panel can monitor those through a relay so a fire signal reaches the monitoring center, but detection stays on the life-safety system.

What does an access-controlled door cost compared with a keypad deadbolt?

A battery keypad deadbolt is a few hundred dollars with no wiring. A true access-controlled door — reader, strike or lever, request-to-exit, door-position switch, supervised power — runs roughly $1,200 to $3,000 installed, more with maglocks. The difference buys audit logs, remote credential changes, and hardware that survives Utah winters.

Tell us what you’re working on

We reply within a couple of hours during business hours — a day at most. You’ll get a straight read on scope, sequence, and budget before anyone commits to anything.

Request an estimate   (385) 236-1741