Renovation & Build-Outs

Herringbone, Chevron & Parquet Flooring in Utah County

Herringbone, chevron, and parquet are pattern floors: short hardwood pieces laid at angles to each other instead of in long straight runs, so the floor becomes the room’s main design element. Grandview Contractors installs them across Utah County and Salt Lake County under a Utah DOPL B100 general contractor license, laid out from the room’s true centerlines so the pattern lands where the eye does.

Discuss a project   Or call (385) 236-1741

Sunlit room with a newly installed hardwood floor ready for furniture in a Utah County home
Fit

Herringbone, chevron, or parquet — which pattern, and when

The three names aren’t interchangeable. Herringbone uses rectangular pieces with square ends; each piece butts into the side of the next at 90 degrees, producing a broken zigzag. Chevron uses pieces with ends cut at an angle, usually 45 or 60 degrees, so the two legs meet at a point and read as a continuous V. Parquet is the family name for block patterns assembled into squares — basket weave, brick, Versailles, and the small oak tiles in many mid-century Salt Lake and Provo homes.

Herringbone is the choice when you want pattern with some tolerance; square-ended pieces forgive a slightly off-square room. Chevron suits a long rectangle with one dominant sightline, because the V pulls the eye down the room — but it needs factory-milled left and right pieces and square walls, or it shows. Parquet fits entries, formal dining rooms, and period restorations where a 12″ or 18″ block grid matches the room’s scale.

If you want a long, calm floor, straight-lay solid hardwood or a wide-plank floor gets there for less. If you want pattern only at a focal point, a border or medallion in a straight floor is often the better spend. Pattern floors are one piece of our flooring installation services and the renovation work they usually sit inside.

The work

What a herringbone or chevron install actually involves

Most pattern floors we install here are engineered hardwood. Short pieces of 3/4″ solid wood carry a lot of end grain per square foot and move more visibly than long planks; engineered construction holds the pattern tighter through our dry winters, though solid herringbone still suits a period house with a wood subfloor and a site-finish plan. Slats run from about 2 1/4″ × 9″ up to 5″ × 24″; a length-to-width ratio near 4:1 or 5:1 keeps the pattern readable rather than blocky.

  1. Prep the subfloor flatter than usual. Straight-lay hides a slight hump; a pattern floor can’t, because every short piece bridges it at an angle and rocks. We want 1/8″ over 10 feet, which usually means self-leveling. Over a slab, we moisture-test first — the expansive clay under much of the valley floor moves and wicks, and a glue-down pattern floor fails from below.
  2. Find the true center. We snap the centerline on the dominant sightline — entry door to fireplace, or down a hall — and a second line square to it. The pattern’s spine runs on that line, not parallel to whichever wall is straightest.
  3. Set the starter course. A plywood nailing strip goes down at exactly 45 degrees to the centerline, and the first courses are glued and pinned to it before it’s removed. A sixteenth of error here becomes visible drift ten feet away.
  4. Lay the field. Engineered pieces go into full-spread urethane adhesive, nailed through the tongue where the product allows; solid slats get glue-assist plus cleats. We work out from the center both ways, checking the spine against the chalk line every few courses.
  5. Cut the border. A pattern floor ends in a sawtooth, so a picture-frame border of one to three straight boards runs the perimeter, absorbing out-of-square walls and giving the pattern a deliberate edge.
  6. Finish. Prefinished pattern floors show a micro-bevel at every one of their many joints; site-finished floors need a multi-head sander, since a drum sander crosses the grain of every other piece. The prefinished vs site-finished choice matters more here than on any other hardwood floor.

We are fond of straight lines and straight answers.

Layout, fastening, and adhesive follow National Wood Flooring Association guidelines and the manufacturer’s spec.

Hands drawing a floor pattern layout with a ruler and pen before a herringbone installation
Close view of hardwood floor pieces showing grain direction and texture after installation
Budget

What does herringbone flooring installation cost in Utah?

As ballpark planning numbers, a herringbone engineered hardwood floor in Utah County typically lands between roughly $14 and $24 per square foot installed, material included — about 50 to 100 percent more than straight-lay of the same product. Chevron sits at or above the top of that range; parquet varies with the pattern and the wood. Ranges for budgeting, not a quote.

Two things drive the gap. Labor: layout, the starter course, the border, and hundreds of angled cuts take two to three times the hours of straight-lay. Waste: plan on 15 to 20 percent extra material for herringbone, more for chevron, because every piece that meets a wall is cut.

One Utah note: UV at 4,500 feet is intense, and near south-facing glass a pattern floor’s alternating grain reads lighter on one leg and darker on the other as the wood colors. That’s the pattern working, not a defect; matte finishes and slow-ambering species like white oak keep it subtle.

Questions we actually get

Can herringbone or chevron go over a concrete slab or in a basement?

Yes, with engineered hardwood in a full-spread glue-down, once the slab passes a moisture test and is ground or leveled flat. Solid herringbone can’t be fastened to concrete and doesn’t belong below grade. Utah County basements also sit on high-radon geology, so test for radon before any finish floor is glued down, not after.

Why does a pattern floor cost so much more than straight planks of the same wood?

Time and waste. Layout from a true centerline, a 45-degree starter course, a scribed border, and an angled cut at every wall double or triple the labor hours, and 15 to 20 percent of the material ends up as offcuts. The wood may cost the same; the floor doesn’t.

Will the pattern show gaps in winter?

Short pieces have more joints per square foot than planks, so seasonal movement shows as many tiny lines instead of a few larger ones. Engineered construction, proper acclimation, and keeping indoor humidity above 30 percent through a dry Wasatch Front January keep that movement small. Hairline winter gaps that close by summer are normal; cupping is not.

Related services

If an existing herringbone floor just needs new life, sanding and refinishing usually beats replacement. Like every Grandview project, the work runs under one B100 general contractor license you can verify at dopl.utah.gov.

Tell us what you’re working on

We reply within a couple of hours during business hours — a day at most. You’ll get a straight read on scope, sequence, and budget before anyone commits to anything.

Request an estimate   (385) 236-1741