Specialty capabilities · Mezzanines & platforms

Ladders & ship’s ladders in Utah County

A ship’s ladder is a steep steel stair — 50 to 70 degrees — with flat treads and handrails on both sides, used where a full stair won’t fit and a rung ladder isn’t safe enough. Grandview fabricates and installs ship’s ladders and fixed access ladders for mezzanines, equipment platforms, and roof hatches across Utah County and Salt Lake County under a Utah B100 general contractor license.

Discuss a project   Or call (385) 236-1741

Welder in safety gear joining a steel stringer for a ship's ladder in a fabrication shop

When a ship’s ladder is the right call

Access steel comes in three steepnesses, and code decides which you may use. A conventional stair runs 30 to 50 degrees and eats 10 to 14 feet of floor per story — that’s steel stair fabrication. A fixed rung ladder runs 75 to 90 degrees and takes almost no floor, but you climb it facing the rungs. A ship’s ladder sits between: a 4-to-6-foot footprint, climbed facing forward with a toolbag.

Under current Utah-adopted code, a ship’s ladder is generally permitted as access to small mezzanines serving a handful of occupants, to catwalks and equipment platforms used only for maintenance, to conveyor crossovers, and to roof hatches. It is not an egress stair for a 2,000-square-foot storage mezzanine with a crew working on it — that needs a real stair, and we say so before anyone falls in love with the floor space a ladder would save.

What goes into a fabricated ship’s ladder

The geometry is tightly prescribed, which is why these are fabricated rather than improvised. Treads need at least 4 to 5 inches of depth, risers stay under 9½ inches, clear width between stringers is a minimum of 18 to 20 inches depending on which code governs, and handrails run continuous on both sides. We lay out rise and run from field measurements, not the architectural section.

  • Stringers: structural channel or ¼-inch plate, cut so the top tread lands flush with the deck edge
  • Treads: serrated bar grating for shops and exterior work, checker plate for clean interiors
  • Handrails: 1¼- or 1½-inch pipe both sides, returned at the ends and carried past the top landing so there is something to hold while stepping off
  • Top connection: welded or bolted to the platform’s edge beam, never hung from decking
  • Base: plated and anchored to the slab, anchor type matched to slab thickness and condition

Interior ladders get shop primer and powder coat. Anything on a roof along the Wasatch Front lives at 4,500-plus feet under intense UV and a hundred-odd freeze–thaw days a year, so exterior units are hot-dip galvanized with serrated treads so a skiff of January ice doesn’t make the first step the last one.

Close-up of a weld joining a pipe handrail to a steel ladder stringer

Fixed rung ladders and roof access

Where even a ship’s ladder won’t fit — a tight mechanical room, a tank, a roof hatch in a corridor ceiling — we fabricate fixed vertical ladders: round-bar or pipe rungs at uniform spacing, held off the wall for toe clearance, with side rails extended above the landing or a walk-through rail. Roof hatches get a telescoping safety post that locks upright when the hatch opens.

Under OSHA’s walking-working surfaces standard, a cage no longer counts as fall protection on new fixed ladders taller than 24 feet; those need a ladder safety system or personal fall-arrest anchorage, and existing caged ladders face a deadline. Replacing an old caged roof ladder is the moment to design that in.

And because the Wasatch fault runs the length of our service area, a tall ladder serving an equipment platform is anchored and braced for lateral load, not just for the weight of the person on it. The connection details look heavier than a catalog drawing. They’re supposed to.

Industrial shop interior with steel walls where a ship's ladder would serve an overhead parts loft

How a ladder project runs

  1. Confirm what code allows. We check the occupant load and use of the space being reached, and verify with the local building department when the stair-or-ladder call is close.
  2. Field-measure. Floor-to-deck rise, available run, headroom at the top, and what’s in the way — conduit, sprinkler mains, racking. Those numbers go straight to the cut list.
  3. Fabricate and finish. Welded as one unit where it fits through the door, two bolted sections where it doesn’t. Finish is applied in the shop, not sprayed on site.
  4. Install and anchor. Usually a half day to a day per ladder, with inspection if the platform permit calls for one.

What does a ship’s ladder cost in Utah?

As a ballpark planning number — not a quote — a custom-fabricated steel ship’s ladder installed in Utah typically runs about $4,000 to $10,000 for a single flight to a mezzanine or platform, handrails and anchorage included. Fixed rung ladders generally land between $2,000 and $7,000; a ladder safety system or walk-through rail pushes a tall one toward the top of that range.

What moves the number: total rise, galvanizing versus powder coat, whether a landing is needed, and whether the ladder must be split to get into the building. Pairing it with a handrail run on the same visit beats two mobilizations.

Questions we actually get

Can we use a ship’s ladder instead of a stair to our mezzanine?

Only in limited cases. Current Utah-adopted code generally allows a ship’s ladder for small mezzanines with a low occupant load, maintenance-only equipment platforms, and roof access. A mezzanine people work on all day needs a conventional stair. We confirm this against your occupancy and square footage before quoting.

What angle is a ship’s ladder, and why does it matter?

Between 50 and 70 degrees from horizontal. Shallower and it’s a stair subject to stair tread and riser rules; steeper and it’s a ladder, which means rungs and no forward-facing descent. That band is the only range where flat treads, a steep pitch, and two handrails are allowed together.

Does our old caged roof ladder still comply?

Possibly not for long. OSHA stopped accepting cages as fall protection on new fixed ladders over 24 feet in late 2018, and existing caged ladders have a phase-out date for adding a ladder safety system. If yours is tall, inspect the anchorage and rungs now and plan the upgrade with any replacement.

Related access and platform work

Full stairs live under steel stairs, the platforms ladders reach under mezzanines & platforms, and the rest of our metalwork under specialty capabilities. Grandview’s B100 license, #14282236-5501, is verifiable at dopl.utah.gov.

Tell us what you’re working on

Send the rise, the floor space you can spare, and what the ladder reaches — a photo helps. We reply within a couple of hours during business hours, a day at most, with a straight read on whether a ship’s ladder is allowed and what it costs.

Request an estimate   (385) 236-1741