Access Platforms & Catwalks in Utah
A catwalk is a narrow, guarded steel walkway that gets people safely to equipment, rooftop units, or the far side of a conveyor without a ladder and a prayer. Grandview fabricates and installs grated catwalks and access platforms for plants, warehouses, and rooftops across Utah County and Salt Lake County under a B100 general contractor license, engineering and permit included.

When a catwalk is the right call, and when it isn’t
Catwalks solve a routing problem, not a storage problem: a technician climbing a dust collector on an extension ladder, a conveyor that splits the plant in two, rooftop HVAC units reachable only by walking on the membrane. If the goal is a safe path from A to B at height, this is the page.
If the goal is floor area, you want a steel mezzanine, priced by square footage and treated as occupied space. If the platform carries a machine rather than a person, see conveyor and equipment platforms, where vibration and point loads run the design. If the only problem is the climb to an existing platform, a ship’s ladder may be all you need.
Two shapes cover most requests: the crossover, a stair-up, bridge-over, stair-down unit spanning a conveyor or pipe rack, and the runway, a long guarded walkway along a tank row or rooftop. Salt Lake plant owners can also see our industrial platforms and catwalks page.
What goes into a fabricated catwalk
The walking surface is almost always welded bar grating, typically 1-inch by 3/16-inch bearing bars on 19-W-4 spacing, serrated where wash-down, oil, or snow is in play. Grating sits on C6 or C8 channel stringers carried by HSS tube posts or bracket arms. Guardrail runs 42 inches high with a midrail and a 4-inch toeboard so a dropped wrench stays on the walkway. Clear width starts at 22 inches for maintenance access and jumps to 36 inches or more once the catwalk becomes an egress path.
How the catwalk is held up drives everything else:
- Post-supported from the slab. Simplest to engineer and inspect; costs you floor space.
- Hung from roof structure. Keeps the floor clear, but bar joists along the Wasatch Front are usually sized for snow and little else, so an engineer confirms they can take hanger loads or we reinforce them first.
- Bracketed to building columns or equipment frames. Efficient when columns follow the route; welding to existing steel brings special inspection along.
We field-measure the route and every pipe, duct, and cable tray it threads through; on crowded plants we use LiDAR as-built scanning so clearances are real numbers. An engineer sizes members and anchorage. The catwalk is shop-fabricated in 10-to-20-foot modules that fit through your door and onto a scissor lift, with bolted field splices so almost no welding happens over your production line. Swing gates at ladder and stair landings go in last.

Does an access catwalk need a permit in Utah?
Usually, yes. A catwalk attached to the building is a structural alteration, so most Utah cities want stamped engineered drawings and a building permit, and welds to existing steel typically get special inspection. A small free-standing crossover around a machine is sometimes treated as equipment; confirm with your city building department before steel is ordered.
OSHA’s walking-working surfaces standard governs guardrail height, toeboards, and fall protection on any catwalk employees use for maintenance; the building code takes over once the walkway is an egress route. We design to whichever is stricter.
Our service area sits along the Wasatch fault, and the USGS seismic hazard mapping behind Utah’s structural design means anchorage and bracing are sized for lateral load, not just a technician and a toolbag. Rooftop catwalks also catch drifting snow against the units they serve, and that load differs between a valley-floor warehouse in Lindon and a bench building above Draper.
What does a steel catwalk cost in Utah?
As a ballpark planning number, not a quote, a 3-foot-wide grated catwalk with guardrail on both sides generally lands between roughly $200 and $450 per linear foot installed in Utah, with stairs, landings, and engineering added on top. A single conveyor crossover usually prices as a unit rather than by the foot.
- Support method. Slab-mounted posts are cheapest; hanging from roof structure, or reinforcing joists to allow it, costs the most.
- Route complexity. Every turn, elevation step, and squeeze past existing pipe or duct adds fabrication and field fitting.
- Access points. Each stair, ship’s ladder, and self-closing gate is its own small steel scope.
- Finish. Galvanizing costs more than paint and is the better buy outdoors or in wash-down areas.
A site walk gets you a budget range; the proposal firms up once engineering settles the support method.

Questions we actually get
Can you hang a catwalk from our existing roof joists?
Sometimes. Open-web bar joists in most Utah warehouses were sized for roof dead load and snow with little margin, so an engineer checks each joist the hangers land on. Often the fix is a reinforcing angle or a header spanning two joists: more cost, but a clear floor. We settle this before fabrication.
How wide does a maintenance catwalk have to be?
OSHA requires at least 22 inches clear for a walkway used only for worker access and maintenance. If the catwalk doubles as a means of egress or serves an occupied platform, the building code generally pushes clear width to 36 inches or more. We ask how it will actually be used, then design to the stricter rule.
Galvanized or painted: which finish should we choose?
Galvanize anything outdoors, in a wash-down area, or over a process that throws moisture; Utah’s freeze-thaw winters and high-elevation UV wear through paint on exterior steel within a few seasons. Shop primer and enamel is fine in dry, conditioned interiors and costs less. Grating is galvanized almost regardless, because it’s hard to recoat in place.
Can the catwalk go in while the line keeps running?
Usually. Sections are shop-fabricated and field-bolted, so most overhead work happens in short lifts between shifts or overnight. Anchor drilling and welding to existing steel need a cleared zone beneath, so those go in your quietest window. A crossover takes one to three nights; a long runway, about a week.
Related platform and steel work
Catwalks are one branch of our mezzanines and platforms work inside specialty capabilities; the stairs that reach them live under steel stairs and guardrail details under metal railings and handrails. Grandview is a Utah DOPL B100 general contractor, license #14282236-5501, verifiable at dopl.utah.gov.
Tell us what you’re working on
Send a photo of the route and what the walkway needs to reach. We reply within a couple of hours during business hours, a day at most, with a straight read on support method and budget.