Steel Trash Enclosure Frames in Utah
A steel trash enclosure frame is the welded gate-and-post system that makes a dumpster enclosure work: tube-steel leaves, pipe posts in concrete, guard posts, and hold-open hardware for the hauler. Grandview fabricates and installs them for restaurants, multifamily, and commercial sites across Utah County and Salt Lake County under a Utah B100 general contractor license.

When a fabricated steel frame is the right call
Choose a fabricated steel enclosure frame when a hauler opens the gates several times a week, when a truck can clip the enclosure, or when the city’s site plan requires an opaque enclosure with latching gates. Those conditions wear out wood and vinyl gates in a season or two; a welded steel leaf on heavy pipe posts holds its square for years.
This is a narrower scope than our custom steel gates and fencing work. A custom driveway gate is built to look good and swing twice a day; an enclosure gate is built to take a front-loader bumping it and be rebuilt cheaply when a truck finally wins. If the whole enclosure is new — walls, footings, apron, and gates — our complete dumpster enclosure scope covers it. Where the risk is a vehicle hitting the walls, bollard installation is the sibling scope, usually set in the same pour.
What goes into a steel trash enclosure frame
A two-leaf frame for a 6- or 8-yard container spans a 12- to 14-foot opening. Each leaf is 2-inch square tube, 11-gauge or heavier, with a mid-rail and diagonal brace so it can’t rack when slammed. Infill is steel panel welded to the frame, or composite or cedar slats on welded tabs where the city only requires visual screening.
- Gate posts — 4-inch schedule 40 pipe or 4×4 tube, set 36 to 42 inches deep, capped so water can’t sit inside and freeze
- Hinges — weld-on barrel hinges with grease fittings, sized to the leaf weight with the infill on it, not the bare frame
- Hold-opens — cane bolts dropping into sleeves cast in the apron at the closed and fully open positions
- Guard posts — 6-inch concrete-filled pipe at each gate post and inside corner, so forks hit steel before masonry
- Pedestrian gate — a 3-foot leaf in the side wall so tenants never open the main gates
The enclosure gets hit, hosed, and splashed with de-icer every winter, so finish matters. We recommend hot-dip galvanizing under powder coat; shop primer and paint is the budget option and needs touch-up by the second spring.

How we build and set one
Most enclosure frames go from site measure to swinging gates in three to five weeks, with the gates out of service for a day or two. The plans may change. The standard does not.
- Measure with the hauler in mind. We check opening width, approach angle, and swing clearance. Haulers want gates that open past 90 degrees and lock back; a leaf that stops at 90 gets torn off within a year.
- Design and approvals. You get a drawing with leaf sizes, post spec, hinge and hold-open layout, and finish. Enclosure height, opacity, and gate rules come from each city’s site-plan standards, so we verify with the local planning department first.
- Fabricate and finish. Leaves and posts are jigged and welded in the shop to field dimensions, then galvanized and powder-coated, which is why they hang square the first time.
- Footings and guard posts. Holes go below frost depth and get air-entrained concrete, because a footing along the Wasatch Front sees a hundred-plus freeze-thaw days a year. On bench lots with the collapsible or expansive soils mapped by the Utah Geological Survey, we size footings for the ground that’s there.
- Hang, adjust, cast the sleeves. Gates are hung, hinges greased, and cane-bolt sleeves set at the exact open and closed positions. Where the apron is being replaced too, our concrete flatwork crew pours it in the same mobilization.

What does a steel dumpster enclosure frame cost in Utah?
As ballpark planning numbers: a fabricated, galvanized, and powder-coated two-leaf gate frame with posts and footings for a 12- to 14-foot opening typically runs $4,500–$9,500 installed. A pedestrian gate adds roughly $900–$1,800, and concrete-filled guard posts run about $500–$900 each. Replacing worn leaves on sound existing posts is often the cheapest fix, usually $2,500–$5,500 for the pair.
What moves the price
Infill is the biggest lever — solid panel costs more than slats, which cost more than open mesh where allowed. After that: galvanizing versus paint, leaf size, how much masonry or apron gets cut and patched around new footings, and whether pickups force a night or weekend install. Several enclosures on one property bring the per-enclosure price down. These are planning ranges, not a quote; after a site visit you’ll get a budget range, then a firm written proposal before any steel is cut.
Questions we actually get
Why do our enclosure gates keep sagging and dragging?
Usually the hinges were sized for the bare frame rather than the frame with infill on it, or the posts sit in shallow footings that heave each winter. Wind is the other culprit — a solid 7-foot leaf catches a canyon gust like a sail and wrenches the hinge side. Heavier hinges, deeper air-entrained footings, and hold-open hardware fix it.
Can you replace just the gates and reuse our posts?
Often, yes. If the posts are plumb, sound at grade, and not lifting, we fabricate new leaves to fit them and weld on new hinges. We check the posts first, because new leaves on posts that already lean only move the problem a year down the road.
What is the biggest cost surprise on an enclosure frame job?
The apron. If the concrete in front of the enclosure is cracked or heaved, cane-bolt sleeves have nothing sound to sit in and the truck keeps breaking the slab edge. Replacing that apron with a thicker, reinforced pad is a separate line item we flag during the site visit, not after the gates are hung.
Are you licensed for this work?
Yes. Grandview Contractors holds a Utah DOPL B100 general contractor license, #14282236-5501, verifiable at dopl.utah.gov, and we’re insured. Fabrication, welding, footings, concrete, and installation all run under that license.
Related steel and site work
One scope in our steel, welding & specialty family. It often pairs with custom steel gate fabrication, a steel security fence, or multifamily construction site work.
Tell us about your enclosure
Send a photo of the gates and the opening width, or just the address. We reply within a couple of hours during business hours — a day at most — with a straight read on scope and budget.