Specialty capabilities · Exterior steel

Custom steel gates in Salt Lake City

A custom steel gate is a driveway, pedestrian, or courtyard gate leaf fabricated to your exact opening — frame, infill, hinges, and latch built as one welded unit instead of a catalog panel trimmed to fit. Grandview fabricates and hangs them across Salt Lake County and Utah County under a Utah B100 general contractor license.

Discuss a project   Or call (385) 236-1741

Custom fabricated steel driveway gate leaf with welded tube frame and picket infill

When a custom gate is the right call

Order a fabricated gate when the opening, the grade, or the design won’t accept a stock leaf: a driveway wider than 12 feet, a sloped approach the leaf must clear as it swings, a side yard too tight to swing at all, or an HOA or historic-district review that wants the gate to match the house. Replacing a gate that sags is the other common call.

This page is about the gate leaf itself. For a full fence run or an automated entry with operators and keypads, start at custom steel gates, fencing and automation. For fixed vehicle barriers, see bollard installation; for a screened refuse corral with steel-framed doors, see steel dumpster enclosure frames; for guardrails, metal railings and handrails.

How a steel gate leaf is actually built

A gate is a cantilever: its whole weight hangs off one post through two or three hinges, and every detail serves that fact. We frame leaves from square steel tube — 2-inch at 11 or 14 gauge for pedestrian gates, 2½- or 3-inch heavier-wall tube for driveway leaves over 8 feet. A diagonal brace runs from the top of the latch side to the bottom of the hinge side so the steel carries the sag in compression instead of asking the welds to. Infill is welded inside that frame, not bolted to it.

Hinges are where cheap gates fail. Anything over about 150 pounds hangs on weld-on barrel hinges with sealed bearings, or adjustable hinges so we can re-plumb the leaf after the posts settle. Frost matters: along the Wasatch Front a shallow post can heave a quarter inch in a hard winter, enough to drop a latch out of alignment. Gate posts go in air-entrained concrete footings below frost line, the hinge post larger and deeper than the latch post because it carries the load.

Every tube is capped or fitted with weep holes so meltwater can’t freeze inside and split a seam. Double leaves get a positive latch plus a drop rod into a ground sleeve. Any gate that meets a salted driveway gets hot-dip galvanizing under powder coat — the zinc handles ice melt, the powder handles Utah sun at 4,300 feet.

Welding a steel gate frame joint in the fabrication shop before fit-up and finish

Swing or slide — and how we decide

Swing gates are simpler and cheaper — our default for driveways up to about 16 feet with a flat approach. A cantilever slide earns its cost when the approach rises more than a few inches across the swing arc, when the driveway is too short to park without blocking the leaf, or when a 20-foot-plus commercial opening would need double leaves heavy enough to need engineering. A cantilever needs roughly half the opening width again in run-back room along the fence line — often the deciding constraint on a narrow Avenues or Sugar House lot.

  1. Measure in three places. Width at grade, at hinge height, and at the post tops, plus grade across the swing arc. Openings are rarely square; the leaf is built to what’s there.
  2. Design and approvals. You get a dimensioned drawing with tube sizes, infill, hinges, latch, and finish. Salt Lake City regulates gate height by zone and street frontage; we confirm current rules with Salt Lake City Building Services before fabrication, and schedule any HOA review.
  3. Fabricate flat, then square. The leaf is tacked on a level table, checked diagonal-to-diagonal, then welded in a sequence that keeps heat from pulling it out of square.
  4. Set posts, then hang. Footings cure before the leaf arrives. We plumb the hinge post under load, set a 2- to 4-inch bottom clearance so snow and plow berms don’t jam the gate, and adjust the latch last.
Grinding a welded joint on a steel gate frame before galvanizing and powder coat

What does a custom steel gate cost in Salt Lake City?

As ballpark planning numbers: a custom steel pedestrian gate with posts and footings typically runs $1,500–$4,000 installed. A swing driveway gate in plain picket usually lands between $6,000 and $12,000; cantilever slides and ornamental or privacy-infill driveway gates run roughly $10,000–$18,000. Those cover leaf, posts, footings, hinges, latch, and finish — automation is a separate line.

What moves the price

Leaf width and weight come first, because they set tube size, hinge class, and footing depth together. After that: infill (open pickets at the low end, laser-cut panels or solid privacy sheet at the top), finish system, cantilever rollers instead of hinges, and site conditions — coring into existing concrete, cobble in the footing holes, or a raked leaf for a slope. You get a budget range after a site visit and a firm proposal before any steel gets cut.

Questions we actually get

Why does my current gate drag, and will a new one do the same?

Almost always one of three things: no diagonal brace so the frame has racked, hinges worn oval, or a hinge post that heaved on a shallow footing. A new leaf fixes the first two; we fix the third by resetting the hinge post below frost depth. Sometimes the honest answer is a new post and hinges on your existing leaf.

What limits how wide a single swing gate can be?

Weight and leverage. Past about 12 feet a single leaf needs tube and hinges heavy enough that a double swing or a cantilever slide usually makes more sense. Wind exposure lowers that limit, since a solid-infill leaf catches a gust like a sail. We’ll tell you where your opening sits before you pick a style.

Do I need a permit for a steel gate in Salt Lake City?

Often not for a gate within zoning height limits, but taller gates, gates on a retaining wall, and new electrical for an operator usually do. Rules differ by zone and city, so we verify with the local building department as part of the project. Grandview holds Utah DOPL B100 license #14282236-5501, verifiable at dopl.utah.gov, and is insured.

Tell us about the opening

Send a photo of the opening and a rough width. We reply within a couple of hours during business hours — a day at most — with a straight read on swing versus slide, finish, and budget. Gates are one scope in our steel, welding and specialty family.

Request an estimate   (385) 236-1741