Interior door installation
Interior door installation covers the hinged passage doors inside a home — bedroom, bathroom, closet, pantry, and the garage-to-house door — from one door that never latched right to a whole-house swap from hollow-core to solid-core. Grandview hangs, cases, and adjusts interior doors across Utah County and Salt Lake County under a B100 general contractor license.

When a hinged interior door is the right choice
A hinged door is the right answer for almost every room that needs privacy or a sound buffer: it seals against a stop on three sides, holds a privacy lock, and costs less than any alternative. If the swing eats floor space you can’t spare — a tight hallway bath or a pantry opening into a walkway — a sliding barn door gives the opening back, at the cost of a real seal. If you want two rooms to read as one when they’re open, an interior French door pair between a dining room and a den does what a single leaf can’t.
One interior door is in its own category. The door between an attached garage and the living space is a separation door under current Utah-adopted code, which follows the International Residential Code: solid wood, solid-core, or a listed 20-minute assembly, and self-closing. We treat that one as a fire-rated door installation even inside a whole-house package, and we don’t swap it for a hollow-core six-panel to match the hall.
The work arrives as a single damaged door, a package for a basement finish, a whole-house replacement of builder-grade hollow-core, or unit-turn door work repeated across a building.
Pre-hung, slab, or split-jamb: what the work actually involves
Three decisions set the scope. Pre-hung or slab. A pre-hung door arrives hinged into its jamb and replaces the whole unit with a fresh, square frame. A slab-only swap keeps the existing jamb, which works only if that jamb is plumb and the new slab can be mortised to match the old hinge and strike locations. Core. Hollow-core doors are light, cheap, and sound like it; solid-core MDF weighs three times as much, blocks noise, and takes paint without telegraphing grain; solid wood looks the part under stain but moves with humidity. Jamb width. A 2×4 wall with half-inch drywall takes a 4-9/16-inch jamb; a 2×6 wall takes 6-9/16. Order the wrong one and the casing never sits flat.
The hanging is where a door earns its keep. We set the hinge-side jamb dead plumb, shim behind every hinge, and drive a 3-inch screw through the top hinge into the framing so the door never sags. Then we shim the strike side to an even 1/8-inch reveal, confirm the door stays put instead of drifting, and only then nail the casing. We are fond of straight lines and straight answers.
Two details people notice later. The undercut: about 3/4 inch over carpet, 1/2 inch over hardwood or tile. Many Utah homes run a single central furnace return, so bedroom doors are undercut on purpose to let air get back to it — close that gap and the room runs stuffy. And hardware: a 2-3/8-inch backset lever in passage, privacy, or dummy function, chosen room by room, with a mortised strike so the latch clicks home without a shoulder.

How we run an interior door package
- Walk and measure every opening. Handing, slab width (24 to 36 inches), height, jamb depth, floor finish on both sides, and plumb. Older Provo, Orem, and Salt Lake City homes often have openings that racked as the house settled; those get pre-hung or split-jamb units that adjust to an out-of-square wall.
- Specify and order. Style, core, hardware finish, and hinge color in one schedule so sixteen doors arrive matching. Stock six-panel and flat-slab doors ship in days; custom heights for 9-foot ceilings and stained wood run weeks.
- Acclimate. Doors sit inside the house two or three days before hanging. Utah’s forced-air winter indoor air is dry enough that a solid wood door hung straight off the truck can shrink at the stiles and show a gap at the stop by February.
- Hang, case, and adjust. Plumb, shim, screw, reveal, stop, casing. On a remodel we match the existing casing profile or replace the run so new and old never meet mid-hallway.
- Finish. Nail holes filled, caulked, primed, and painted — door and casing — through our interior painting scope, so the door isn’t a chore left behind.
What does interior door installation cost in Utah?
As a planning ballpark, a painted hollow-core pre-hung door installed and cased typically runs a few hundred dollars; solid-core or stained wood pushes each one into the high hundreds. Whole-house packages of twelve to eighteen doors commonly land in the low five figures with hardware and painting. These are ranges, not promises — a measured estimate is where numbers get firm.
What moves the price: pre-hung versus slab; core and species; hardware grade; site painting versus factory-primed; casing replacement versus reuse; and openings that need re-framing. The garage separation door costs more than a bedroom door because the self-closer and listed assembly aren’t optional, and an odd-width opening in a 1960s rambler may need its rough opening rebuilt first. This scope sits in the site, structure & envelope family for a reason — occasionally the door problem is a framing problem.

Questions we actually get
Can I replace just the door slab and keep the existing jamb?
Yes, if the jamb is plumb, sound, and standard-sized. We mortise the new slab to match the existing hinges and strike — slower per door than a pre-hung swap, but it keeps your casing and paint intact. If the jamb is racked or the hinges have pulled loose from the framing, a pre-hung unit is the honest fix.
Do new interior doors need a permit?
Replacing a door in an existing opening generally doesn’t. Resizing, moving, or adding an opening in a load-bearing wall does, because it’s framing work. The garage-to-house door is the one to ask about — it must stay a rated, self-closing assembly, and an inspector will look for it during any permitted basement work; verify specifics with your city’s building department.
Will solid-core doors fit where hollow-core doors were?
Usually. Both are 1-3/8 inches thick and share standard widths. The differences are weight — a solid-core slab wants three hinges and long screws into the framing — and the undercut, which we re-check so return air still has a path under the door.
How long does a whole-house interior door package take?
Once doors are on site and acclimated, a crew hangs and cases roughly six to ten pre-hung doors a day, so a typical house is two to three days of carpentry plus painting. Lead time is stock styles in days, custom heights or stained species in weeks. Every window and door project we run gets a written schedule first.
Tell us what you’re working on
One sticking door or a whole house of them — we’ll give you a straight read on pre-hung versus slab, core, and budget before anyone commits. We reply within a couple of hours during business hours, a day at most.