Site, structure & envelope

Egress window installation

An egress window is a cut-in basement window large enough to climb out of, paired with an excavated well and, where the well is deep, a ladder. Current Utah-adopted code requires one in every basement bedroom, and Grandview installs them under a B100 license — saw cut, well, drainage, and window as one scope.

Discuss a project   Or call (385) 236-1741

Finished basement bedroom with daylight from a new egress window

When an egress window is the right scope

You need this if a basement room is going to be slept in. Utah’s adopted residential code requires an emergency escape opening in every basement sleeping room, and a hopper window up near the joists does not qualify. That makes the egress window the gate to a legal basement finish or a bedroom you can count when the house sells. Our egress window planning page covers the layout side; this page is the installation itself.

It’s a different job from our other window work. Replacement windows reuse an opening that already exists. New-construction windows go in before the wall is closed. An egress install cuts a new opening through a foundation wall that’s holding back soil, then builds the well that keeps that soil and its water out. It’s half window, half foundation work — which is why it sits under site, structure & envelope with the rest of our window and door installation. An undersized existing window can often be enlarged downward instead, which is cheaper than a fresh cut.

What the window and well have to meet

The numbers that govern the opening are well established and worth knowing before you shop for a unit. The window needs a net clear opening of at least 5.7 square feet, at least 20 inches wide and 24 inches high, with the sill no more than 44 inches above the finished floor. That’s the opening with the sash open — not the glass size and not the rough opening. A 36-by-48 casement typically clears it; many sliders that look big enough don’t. The well needs roughly 9 square feet of floor area projecting at least 36 inches from the wall, and once it’s deeper than 44 inches it needs a permanently attached ladder. Well and cover details vary by city, so we confirm them with your building department during permitting.

Materials follow from the wall. Poured concrete gets a wet saw cut and a pressure-treated or steel buck; block walls usually need a lintel above the cut because the cores above carry load. Wells come in galvanized corrugated steel, composite, or built-in-place block when the finish matters. The unit is usually vinyl or fiberglass, set directly into the buck; a casement opens its full width in one motion, which is the point.

How we sequence an egress install

  1. Locate. We check the exterior wall for buried gas, water, and sewer lines, measure footing depth, and confirm setbacks before picking the spot.
  2. Permit. Cutting a foundation wall is permitted work in every city we serve; we pull it and schedule the inspection.
  3. Excavate. The pit goes about a foot below the planned sill and wide enough to set the well — a mini-excavator in most yards, by hand where access is tight.
  4. Cut. A water-fed wall saw makes the opening from outside, with the room inside sealed off from slurry. If a footing or beam pocket is in the way, we re-plan rather than cut through it.
  5. Buck, set, and seal. Treated buck anchored to the concrete, window set plumb and level, flange or frame sealed, exterior foam and sealant at the perimeter.
  6. Drain and backfill. A 12-inch gravel bed under the well, tied to the footing drain where one exists; well anchored to the wall, ladder bolted in, backfill compacted and graded away from the house.
Compact excavator digging a window well pit beside a foundation wall

What an egress window costs in Utah

As a ballpark planning number, a cut-in egress window with a standard well runs roughly $3,500 to $7,500 in Utah County and Salt Lake County. The number moves for specific reasons: thick poured walls and block walls that need a lintel take longer to cut; deep wells on bench lots need ladders, taller well sections, and more excavation; relocating a gas meter or sprinkler main adds a trade visit; composite wells and polycarbonate covers cost more than open corrugated steel. A consultation gives you a budget range; the estimate after we see the wall and yard is the number to plan on.

Two Utah conditions belong in the budget. Much of the Wasatch Front sits on expansive clay or collapsible bench soils, documented by the Utah Geological Survey; backfilling a well with the clay you dug out invites heave and a leaning well, so we backfill with gravel in compacted lifts. And summer cloudbursts find undrained wells fast — if there’s no footing drain to tie into, we settle window well drainage before we close the hole, not after the first August storm.

Bright finished basement with carpet and recessed lighting, now a legal bedroom

Questions we actually get

Does cutting an egress opening weaken my foundation?

Not when it’s done right. A properly bucked opening below the sill plate with the footing intact behaves like an opening formed at the original pour. What causes trouble is cutting into a footing, a beam pocket, or a corner, which is why we locate the window before anyone starts a saw.

Can the egress window go in before the rest of the basement finish?

Yes, and it usually should. The excavation and wall cut are messy, outdoor, and weather-dependent; framing and drywall are not. We often install the egress window as the first inspected item on a basement project, then release the interior trades. If you’re finishing in stages, the window stands alone as long as you need.

What drives the cost up on a specific house?

Wall thickness and material, well depth, and what’s buried outside the wall. An 8-inch poured wall on a flat lot with clear access is the easy case. A block wall, a bench lot with five feet of backfill, or a gas line on that side of the house each add real hours, and we flag them at the site visit.

Should I think about radon when I add a basement bedroom?

Yes. Utah’s geology produces elevated indoor radon in many homes, and a basement bedroom means more hours at the lowest level. The EPA’s radon guidance covers testing; a short-term test before the finish is cheap and tells you whether a mitigation rough-in belongs in the scope.

Tell us what you’re working on

Send a photo of the basement wall and where the bedroom will be. We reply within a couple of hours during business hours — a day at most — with a straight read on scope, sequence, and budget.

Request an estimate   (385) 236-1741