Egress Window Well Drainage
A window well is a bucket bolted to your foundation, and without a drain at the bottom it fills until water comes over the sill. Grandview installs gravel sumps, footing-drain tie-ins, and interior sump connections for egress wells across Utah County and Salt Lake County under a B100 license.

When the well is the problem, not the wall
The tell is simple: water on the basement floor directly under a window, a stained sill, and a well floor still muddy days after a storm. If the rest of the wall is dry, you don’t need the full exterior excavation and membrane job. You need the well to drain.
Egress wells are the usual offenders because they’re big: a code-sized well holds 25 to 40 gallons before anything spills, and it catches roof runoff, sprinkler overspray, and drifted snow all winter.
This page covers draining the well itself. If the window isn’t a legal egress yet, start with egress window installation, which includes a new well and drain as one scope. If the whole yard is wet, a French drain upstream of the wells solves more than a well drain will. Both sit within our waterproofing and drainage work in the site, structure & envelope family.
Gravel sump, footing tie-in, or interior sump
- Gravel sump. We dig the well floor out 18 to 24 inches, line the hole with filter fabric, and fill it with washed ¾-inch stone. Cheapest option, but only in soils that actually absorb water.
- Footing-drain tie-in. A 3- or 4-inch riser runs from a grated inlet at the well floor down to the perimeter drain at the footing. The right answer when an exterior footing drain exists and still flows. We camera it first; a tie-in to a clogged drain is money spent on nothing.
- Interior sump connection. Where there’s no footing drain, a solid pipe is cored through the wall above the footing to an interior basin. The well becomes one more inlet for the sump pump, sized for the extra inflow.

What the work involves
We start with two elevations: the window sill and the top of the footing. The well floor needs to sit at least 4 to 6 inches below the sill with gravel below that, and the drain inlet has to be the lowest point in the well, not a grate sitting proud of the stone. On older Provo and Orem homes we often find the well set on grade with the sill an inch above the dirt.
Soil decides which drain you get. The Utah Geological Survey maps much of the Wasatch Front as expansive clay and collapsible bench soils, and neither one percolates. A gravel sump in Lehi or Draper clay is a gravel bathtub holding water against the wall. We perc-check the well floor before committing to a sump; in clay we tie in or go to an interior basin.
Then the well itself. Galvanized or composite liners get re-fastened with masonry anchors and sealed at the flanges, because a liner that has pulled away lets backfill wash in and bury the drain. Backfill outside the liner is compacted in lifts so the well doesn’t settle and tilt toward the house, a common failure on bench lots.
Two Utah details change the spec. With 100-plus freeze-thaw days a year along the Front, a riser holding standing water will heave, so it’s sloped and gravel-bedded to stay empty between storms. And because a monsoon cell can drop an inch of rain in an hour, the inlet is sized for a surge, not a drizzle.
Covers are the last piece. A clear polycarbonate cover keeps rain, snow, and leaves out and cuts what the drain has to handle by most of it. On an egress well the cover must open from inside without tools, and a well deeper than about four feet still needs its ladder under current Utah-adopted code; confirm specifics with your city building department before buying a locking cover.
What does window well drainage cost in Utah?
As ballpark planning numbers, not quotes: a gravel sump retrofit in a well with a sound liner typically runs $600 to $1,500. A footing-drain tie-in usually lands between $1,500 and $4,000 per well, with depth driving the spread. Coring to an interior sump sits in a similar range, plus pump upsizing if needed. Polycarbonate egress covers add roughly $200 to $600 each installed. Three wells on one visit cost less per well than three trips.
Up: a liner that needs replacing, a clogged footing drain, wells deeper than five feet, and concrete or landscaping that has to come out and go back. Down: a downspout extension and a cover that keep most of the water out in the first place. We’ll tell you if that’s all you need. Our B100 license is verifiable at dopl.utah.gov.

Questions we actually get
My window well fills up every storm. Is the drain clogged or missing?
Usually missing. Many Utah County wells from the 1970s through the 2000s were set with no drain at all. If there is a grate at the bottom, we flush it and camera the line; one that backs up within minutes is clogged or was never connected to anything.
Can you add a drain to an existing egress well without replacing it?
Yes, in most cases. We excavate the well floor, set the riser and gravel, and re-seal the existing liner if it’s sound. Rusted-through liners or composite wells cracked at the flange get replaced in the same visit. The window stays put.
Does a window well cover count as drainage?
No, but it does most of the work. A cover keeps rain and snowmelt out, so the drain only handles what blows in and what the soil contributes. On egress wells it has to open from inside without tools, which we confirm with your city before installing a locking model.
Will a gravel sump work in my soil?
Only if the soil percolates. Much of the Wasatch Front sits on clay and silty bench soils that don’t, which is why we perc-check the well floor first. If water sits in the test hole for hours, you need a footing-drain tie-in or an interior sump connection instead.
Tell us which well is flooding
We reply within a couple of hours during business hours — a day at most. You’ll get a straight read on whether it’s a sump, a tie-in, or just a cover and a downspout, and a budget range before anyone commits.