Replacement & Retrofit Window Installation
Replacement windows go into an existing home either as inserts that keep the old frame or as full-frame units that strip the opening back to the studs. Grandview installs both across Salt Lake City and Utah County under a B100 license, and tells you which one each opening actually needs.

Insert, full-frame, or a different page entirely
This page is for windows going into walls that already exist. If the wall is being framed now, you want new-construction windows, which flange into the weather barrier before the shell closes. If you’re cutting a new opening into a basement wall for a bedroom, that’s egress window installation, with its own excavation and well. Replacement is the middle case: the opening exists, something in it has worn out, and the question is how much of the old assembly to keep.
Insert replacement (also called pocket or retrofit) leaves the original frame in the wall. The old sashes and stops come out, a new unit slides into the pocket, and exterior trim, siding, and interior casing stay untouched. It’s faster, cheaper, and right when the existing frame is square, sound, and dry. The trade-off is glass: you lose roughly an inch of daylight each direction because the new frame nests inside the old one.
Full-frame replacement takes everything out down to the rough opening — frame, sill, exterior trim — and installs a new flanged unit with a fresh sill pan, flashing, and air seal. It costs more and disturbs the exterior finish, but it’s the only honest fix for rot, water staining under the stool, or flashing that was never there. Many homes need inserts on three walls and a full-frame on the one that faces the weather.
What the existing wall tells us
The Wasatch Front has three common wall types, and each changes the install.
Stucco. Most of Utah County’s 1990s and 2000s subdivisions are stuccoed, and cutting stucco back for a full-frame means patching a finish that rarely matches. When the frame underneath is sound, a retrofit-flange unit with a stucco fin laps over the old frame and seals to the existing finish, avoiding the patch entirely. When it isn’t, we do the full-frame and coordinate the stucco repair so it’s one project rather than two.
Brick. Salt Lake City’s older neighborhoods are full of brick bungalows and ramblers where the window sits in a masonry opening with no nailing flange. These take a block-frame unit shimmed and anchored through the jambs, then sealed with backer rod and sealant at the brick so it doesn’t leak at the brick mold in a spring storm.
Aluminum frames. Many valley homes from the 1970s and 80s still carry single-pane aluminum sliders that conduct cold straight through and sweat in January. Their pockets are often out of square; if the diagonals disagree by more than the unit can shim, a full-frame is the better money.

How a replacement project runs
- Measure and probe. Width, height, and diagonal on every pocket, plus an awl into the sill and lower jambs. Soft wood means a full-frame on that opening, and we’d rather know on measure day than install day.
- Lead check on older homes. In pre-1978 houses, common across central Salt Lake City and downtown Provo, pulling old frames disturbs painted surfaces, so lead-safe practices under the EPA Renovation, Repair and Painting rule apply and containment goes into the schedule.
- Order to the pocket. Replacement units are built to the measured opening, not a stock size, and lead times run several weeks. No sash comes out until every unit is on site and checked against the order.
- One opening at a time. Each window is out and back in within the hour, so the house is never open overnight and we install year-round with low-temperature sealants in winter.
- Seal, insulate, finish. Low-expansion foam at the shim gap, sealant at the exterior perimeter, new stops or casing inside, and an operation check on every sash and lock.

For the glass, the ENERGY STAR Northern climate zone sets the U-factor floor; low-E coatings and gas fills are covered on our energy-efficient window page. This scope lives inside our windows and doors service and the site, structure & envelope family.
What do replacement windows cost in Utah?
As ballpark planning numbers, vinyl insert replacements in the Salt Lake and Utah County market commonly land between $500 and $1,200 per opening installed. Full-frame replacements in fiberglass or clad wood typically run $1,200 to $2,800 per opening, more for large or specialty shapes. Ranges, not quotes; a measured estimate follows the site visit.
What moves the number: the insert-versus-full-frame call on each opening, frame material, operating style, glass package, second-story access, lead-safe containment on pre-1978 homes, and how much exterior finish has to be cut and patched. Whole-house packages price lower per opening than three windows on one wall. Rot repair is the wild card, priced as a separate line so you can see it.
Questions we actually get
Will insert replacement windows make my rooms darker?
A little. The new frame sits inside the old one, so you give up roughly an inch of glass in width and height. On a large picture window it’s barely noticeable; on a small bathroom slider it can matter, and full-frame replacement recovers the original glass size.
Do I need a permit to replace windows in Salt Lake City or Provo?
Like-for-like replacement in the same opening usually doesn’t require a permit; changing the opening size, adding a window, or converting a bedroom window to meet egress typically does. We confirm with the local building department before ordering.
Can you replace windows in a stucco house without wrecking the stucco?
Usually, yes. A retrofit-flange unit with a stucco fin covers the old frame and seals to the existing finish, so no stucco gets cut. The exception is a rotted or badly out-of-square frame, where a full-frame install and stucco patch is the honest fix; we tell you which after measuring.
How long does a whole-house window replacement take?
Once units arrive, a typical single-family home of 12 to 20 openings takes two to four working days on site. The wait is in the ordering: custom-sized replacement units take several weeks from the manufacturer, and we don’t schedule demolition until every unit is delivered and checked.
Tell us what you’re working on
Send us the age of the house, the wall finish, and a rough window count. We reply within a couple of hours during business hours, a day at most, with a straight read on insert versus full-frame and a budget range.