Foundation & Below-Grade Waterproofing
Foundation waterproofing is the membrane, coating, and drainage-board system applied to the outside of a concrete foundation wall before backfill — the primary barrier between wet soil and the wall itself. It belongs on every new basement and crawl-space foundation along the Wasatch Front, and Grandview specifies and installs it under a Utah B100 general contractor license.

When foundation waterproofing is the right scope
This is the wall system for a foundation that’s open to the air: a new pour, a below-grade addition, or a wall already excavated for another reason. An exposed wall is the cheapest moment you’ll ever get to waterproof it. Once backfill goes in, the same membrane costs several times more because you’re paying to dig it out again. It’s one layer of our waterproofing and drainage work within the site, structure & envelope family, installed alongside new foundations and the foundation excavation that exposes the wall.
Exterior basement waterproofing is the retrofit — excavating a finished lot to reach a leaking wall. Interior basement waterproofing manages water after it’s through the wall instead of stopping it outside. An exterior footing drain is the pipe at the base of the wall this membrane drains into, installed in the same trench.
Dampproofing versus waterproofing: the distinction that decides the spec
Dampproofing — the thin black asphalt spray many builders stop at — resists soil moisture. Waterproofing resists water under pressure. Current Utah-adopted residential code allows dampproofing on most basement walls but requires true waterproofing where a high water table or severe soil-water conditions are known to exist. Along the Wasatch Front that covers lots near canals, spring-fed bench subdivisions, and any site whose soils report notes perched water.
Our default on a basement foundation here is a waterproofing-grade membrane with drainage board. The upcharge is modest on an exposed wall, and the Utah Geological Survey has mapped enough expansive clay and shallow groundwater across both valleys that we’d rather not gamble a finished basement on the thin spec.
What a foundation waterproofing installation involves
- Cure and prep. New concrete cures before most membranes will bond — a week or more depending on product and weather. We strip forms, patch every snap-tie hole, grind fins at form joints, and fill honeycombing.
- Detail the cold joint. The seam where wall meets footing is where below-grade water enters most often. We tool a cant at that joint and carry the membrane down over the footing so water sheds past the seam, not into it.
- Apply the membrane. Spray-applied polymer-modified asphalt at roughly 60 mils dry, a self-adhered rubberized-asphalt sheet lapped and rolled, or bentonite panels where the water table is persistent. Penetrations get boots or liquid-flashed collars, not caulk.
- Protect and drain. Dimpled drainage board goes over the membrane before any backfill touches it. It gives water a free path down to the footing drain and shields the membrane from rocks in the fill.
- Terminate and tie in. The top edge is terminated with a bar or sealed edge just below finished grade; the bottom ties into the footing drain and its washed-gravel envelope. We inspect all of it before the first bucket of backfill.

Utah conditions that change the membrane spec
Expansive clay first. When clay against a foundation wets and swells, it pushes laterally; keeping the adjacent soil drained — membrane, drainage board, working footing drain — reduces that pressure as well as the leak.
Backfill second. Many Utah County lots are cut into the bench, and the cobble-and-silt mix that comes out of the trench is poor backfill against a membrane. We specify free-draining granular fill against the drainage board, placed in lifts, with the native material used elsewhere. Backfilling with whatever came out of the hole is the most common way a correct membrane fails by year three.
The calendar third. Most liquid and self-adhered membranes carry minimum application temperatures around 40°F and won’t bond to a frosted wall. With 100-plus freeze-thaw days a year here, that can mean a week’s wait in January or a switch to a cold-weather-rated sheet. Problems happen. Surprises should not.
What does foundation waterproofing cost in Utah?
On a wall already exposed during new construction, ballpark planning numbers run about $1–$3 per square foot of wall for spray dampproofing and roughly $4–$10 per square foot for a waterproofing-grade membrane with drainage board installed. A typical full-basement perimeter lands in the low four figures for dampproofing and the mid four figures to around $15,000 for the full system.
What moves the number: wall height, the count of penetrations and inside corners, a sheet or bentonite system instead of spray, and how long the trench stays open for cure and inspection. If the wall isn’t exposed yet, excavation dominates the cost instead.

Questions we actually get
My builder’s bid says “foundation coating.” Is that waterproofing?
Usually not. “Coating” in a Utah builder’s bid most often means asphalt-emulsion dampproofing, which resists moisture but not water under pressure. Ask for the product name and dry-film thickness. If you have a basement, a bench lot, or a soils report mentioning perched water, ask for a waterproofing-grade membrane and drainage board instead.
Can the membrane go on before the footing drain is in?
It can, but the system doesn’t work until the drain is connected. The wall sheds water down the drainage board; without a footing drain and a discharge path, that water sits at the base of the wall and finds the cold joint. We install both in the same open trench and inspect the tie-in before backfill.
How long does the foundation cure before the membrane goes on?
It depends on the product. Many spray-applied asphalt membranes tolerate green concrete after a few days; most self-adhered sheets want the wall drier, often seven days or more, and some need a primer. We schedule around the product’s cure requirement and the forecast, because rushing a sheet onto a wet, cold wall produces a membrane that peels at backfill.
Does a crawl-space foundation need the same system as a basement?
Same thinking, smaller scale. A crawl-space stem wall sees far less hydrostatic head than an eight-foot basement wall, so dampproofing plus a footing drain is often adequate on well-drained soils. On clay or a lot that collects runoff, we still recommend a membrane, paired with a below-slab vapor barrier inside.
Tell us what you’re pouring
We reply within a couple of hours during business hours — a day at most. You’ll get a straight read on dampproofing versus membrane, the drain and backfill it depends on, and a budget range before anyone commits to anything. Our B100 license is verifiable at dopl.utah.gov.