Network & Wi-Fi Infrastructure
Network and Wi-Fi infrastructure is the equipment layer of a building’s network: ceiling-mounted access points, the PoE switch and router that feed them, the rack they live in, and the fiber handoff from the provider, placed so coverage is designed rather than hoped for. It’s for homes, ADUs, shops, and tenant spaces where Wi-Fi has to work in every room; Grandview coordinates it under a B100 general contractor license, managing the licensed low-voltage trade partners who mount, configure, and test it.

When Wi-Fi infrastructure is the scope, and when it isn’t
This page is about coverage and capacity: how many access points, where they mount, what switch powers them, and where the rack sits. The cable in the walls is structured wiring and data cabling, usually scoped together with this. Lighting scenes and voice control are smart home automation; exterior cameras and a recorder are security camera installation. Both ride on the network described here, which is why we plan it first.
It’s the right fit when one router on a shelf will never reach a 4,000-square-foot home with a finished basement, which describes much of the new construction in Lehi, Saratoga Springs, and Eagle Mountain. It fits a detached shop or ADU that needs real bandwidth, a tenant space where thirty laptops and a point-of-sale system share one network alongside the landlord’s electrical fit-out, and any home where a store-bought mesh kit has been tried and the office still drops calls.
It’s the wrong fit when the building is small, the walls are drywall, and one good router covers it. We’ll say so.
How a wired-backhaul Wi-Fi system is designed and installed
- Coverage plan on the floor plan. Access points go per floor, not per house: roughly one per 1,500 to 2,000 square feet of open plan, more where walls are dense. Stucco over wire lath, common on Utah County homes, behaves like a screen door for radio; poured-concrete basement walls and radiant-barrier roof sheathing do the same. Each AP location becomes a ceiling drop on the wiring map.
- Pick the equipment class. Current access points run Wi-Fi 6, 6E, or 7. The 6E and 7 units add the 6 GHz band, which is fast and uncongested but passes through walls worse than 5 GHz, so it raises AP count rather than lowering it. Homes get a router, a PoE switch sized to the AP and camera count, and ceiling APs; commercial spaces add a managed switch and controller so guest, staff, and point-of-sale traffic sit on separate VLANs.
- Locate the rack. A recessed enclosure or small wall rack in the mechanical room, with a dedicated 20-amp circuit and airflow, because PoE switches run warm in a closed closet. With municipal and private fiber reaching much of Provo, Orem, Lindon, and the north county, we run conduit from the exterior demarc to the rack so the provider’s install is a pull, not a fish.
- Mount and power. APs mount to the ceiling on the Cat6 drop and draw power over that same cable, so no outlet is needed up there. Exterior APs for a shop or long driveway are outdoor-rated units in conduit, because high-elevation UV ruins ordinary cable jackets within a few seasons. Detached buildings get a buried link rather than a wireless bridge unless trenching is impractical.
- Configure, test, document. Channels and transmit power are set so adjacent APs hand off cleanly. Every room gets a signal and throughput check, cameras and IoT devices land on their own network, and you receive a labeled rack, admin credentials, and a one-page map of what’s where.

What does a home Wi-Fi installation cost in Utah County?
As a planning ballpark, not a quote: a wired three-to-four access point system for a two-level home with a basement tends to run $2,500 to $6,000 installed, equipment included, when the ceiling drops exist or go in during a remodel. Commercial tenant spaces with managed switching commonly run $6,000 to $15,000 depending on size and device count.
- Access point count. The main driver. A 2,400-square-foot drywall-and-wood home may need two; the same footage with a concrete basement, stucco exterior, and detached shop may need five.
- Equipment tier. Prosumer gear suits most homes; enterprise-class APs and switches cost two to three times more and earn it in offices and multi-tenant buildings, rarely in a house.
- Cabling already in place. With ceiling drops in, this scope is mostly hardware and configuration. Without them, add the structured wiring cost, cheapest while walls are open during a basement finish or addition.
- Outbuildings and exterior coverage. A trenched link to a shop or ADU adds excavation; an outdoor AP adds conduit and a weatherproof unit.
Consultation, then a budget range, then an estimate once the AP count is settled on the plan. Our license and every trade partner’s are verifiable at dopl.utah.gov. This scope runs inside our MEP and systems coordination work and the wider renovation and build-out family, and it often shares a rack and drop map with home theater and AV wiring.

Questions we actually get
Can’t I just buy a mesh Wi-Fi kit instead of cabling access points?
In a small, open home, yes, and we’ll tell you that. In a larger home, mesh nodes relaying wirelessly lose capacity at every hop, and a concrete basement or stucco wall can break the chain. Wired-backhaul access points cost more to install and perform as one consistent network from the attic to the shop.
Where should the network rack go in a new home?
In the mechanical room or a utility closet on the lowest level, near where fiber enters the house, with a dedicated circuit and some airflow. Avoid the garage, where summer heat shortens equipment life, and the master closet, where a switch fan is never welcome. Decide it before electrical rough-in.
Do I need Wi-Fi 7 equipment, or is Wi-Fi 6 enough?
For most homes Wi-Fi 6 is plenty, and the money is better spent on one more access point in the right spot. Wi-Fi 6E and 7 make sense when many of your devices support the 6 GHz band. The Cat6 drops and rack are the same either way, so the choice can change later.
What happens if the structured wiring isn’t done yet?
The Wi-Fi scope waits on the drops, which is why we scope them together. Each access point needs a ceiling cable and the rack needs a circuit, so the low-voltage and electrical partners are sequenced with framing and drywall. In a finished home we’ll say which drops can be fished and which should wait for a wall that’s opening anyway.
Tell us what you’re working on
We reply within a couple of hours during business hours, a day at most. You’ll get a straight read on scope, sequence, and budget before anyone commits to anything.