Ductwork Installation & Replacement
Ductwork replacement swaps leaking, undersized, or crushed supply and return ducts for a sealed, properly sized distribution system — the fix when rooms never reach temperature no matter how new the furnace is. Grandview Contractors holds the contract under our B100 general contractor license and manages licensed HVAC contractors who perform the work across Utah County and Salt Lake County.

When ductwork replacement beats a new furnace or AC
Ducts are the part of the HVAC system nobody sees, so they get blamed last. A bedroom at the end of the run that stays cold, a furnace that short-cycles because the return can’t feed it, dust that reappears days after cleaning: if the equipment is recent and the complaints persist, the ducts are usually the problem.
Replacement makes sense when the system has flex duct kinked above a ceiling, trunk lines sized for the house before its addition, panned joist bays used as returns, or sheet metal with twenty years of separated joints. It also makes sense when a furnace replacement or AC replacement brings a blower the old ducts can’t carry — 1,600 CFM pushed through ducts built for 1,000 is a noisy, inefficient mismatch.
It is the wrong call when the ducts are sound but unbalanced; that’s a zoning system conversation. For additions the main system was never meant to serve, a ductless mini-split often costs less than extending trunk lines.
What a duct replacement actually involves
Good duct work starts with a load calculation and a duct design, not a roll of flex and a box of zip ties. The HVAC contractor we bring in runs a Manual J load and a Manual D layout from it, which sets trunk dimensions, branch sizes, and each room’s register count.
- Trunk lines in rigid galvanized sheet metal, joints sealed with mastic rather than cloth tape, which dries out and lets go.
- Branch runs in sheet metal or properly supported flex — flex is fine when pulled taut, supported every four feet, and never bent tighter than its own diameter.
- Dedicated return ducts replacing panned joist bays, which leak, pull in dust, and in a basement can depressurize the space enough to draw soil gas through slab cracks. Utah sits on high-radon geology, so sealed returns matter here.
- Insulation on any run outside conditioned space — an uninsulated attic duct in a Wasatch Front July delivers air the attic has already heated.
- Balancing dampers at each branch takeoff, so the system is tuned after installation rather than throttled at the registers.
Sequencing is where general-contractor oversight earns its keep. In a basement finish, the duct layout is settled before framing so soffits are planned, not improvised; where a trunk needs a joist notched, we check structure before anyone cuts.

Why sealed ducts are the whole point
The U.S. Department of Energy notes that typical duct systems lose 20 to 30 percent of their air to leaks and poor joints. A new furnace on old ducts still sends a quarter of its output into the attic or crawl space.
Every joint gets mastic or UL 181 foil tape, and takeoffs are sealed at the trunk. Current Utah-adopted energy code calls for duct leakage testing when new ducts run outside the conditioned envelope, and we schedule that test as part of the scope. Whether a like-for-like duct replacement needs a mechanical permit varies by city — Provo and Orem run established reviews; fast-growth cities like Lehi and Saratoga Springs can set different thresholds — so we confirm with the building department and pull the permit when required.
Tighter ducts often make a balanced ERV or HRV worth adding, and the new layout is the time to plan where it ties in.
What drives ductwork replacement cost in Utah?
Access decides most of it. Ducts replaced in an open basement ceiling or accessible attic cost a fraction of ducts replaced behind finished drywall, where every run means cutting, patching, and repainting. Our ballpark planning range for a full residential replacement along the Wasatch Front runs from the mid-single-digit thousands for an open single-story system to the low teens for a two-story home with finished ceilings and a full redesign. Planning numbers, not quotes — the real figure follows a site visit and a duct design.
Also moving the number: sheet metal versus flex for branch runs, how many new returns the design calls for, whether equipment is replaced at the same time, and whether finish repair is in the scope. Inside a larger remodel run through our MEP coordination, drywall and paint are already in the plan and the duct work rides along.

Questions we actually get
Can you replace just part of the ductwork?
Often, yes. If the trunk is sound and one wing of the house is starved, replacing those branch runs and adding a return can solve it. The duct design tells us whether a partial fix will work or whether the trunk itself is the bottleneck. We’d rather replace less and have it work.
Does Grandview do the duct work itself?
No. HVAC work in Utah is performed by licensed HVAC contractors, and that’s who installs it. Grandview holds the contract, coordinates the duct design with the rest of your project, sequences the work with framing and drywall, and quality-checks it before inspection. Our license and every trade partner’s are verifiable at dopl.utah.gov.
How long is the heat or AC off during replacement?
For a full replacement, typically one to three working days, with the system down for stretches rather than the whole time. We phase the work so equipment reconnects to the new trunk early, and we schedule around weather — nobody loses heat in a January cold snap for a job that could run in April.
Should I replace ducts before or after a new furnace?
Together, ideally. Duct design and equipment sizing depend on each other, and one crew doing both saves labor. If they must be separate, do the ducts first — a new furnace on undersized, leaking ducts underperforms from day one, and some warranties expect airflow within a specified range.
Tell us what you’re working on
We reply within a couple of hours during business hours — a day at most. You’ll get a straight read on scope, sequence, and budget before anyone commits. Duct work is part of our wider renovation and build-out services.