Renovation & Build-Outs · MEP & Systems · Low-voltage

Commercial Access Control

Commercial access control replaces keys with credentials: card, fob, or phone readers at each controlled door, electrified hardware that releases on a valid read, and a controller that logs who went where. Grandview Contractors coordinates the door prep, cabling, licensed low-voltage and electrical trade partners, and the fire-alarm tie-in under one B100 contract for offices, clinics, warehouses, and multi-tenant buildings in Utah County and Salt Lake County.

Discuss a project   Or call (385) 236-1741

Modern office building interior with glass ceiling and steel frames, the kind of multi-tenant space where card-reader doors control suite entry
When this is the right page

When commercial access control is the job, and when a sibling page fits better

This page covers controlled doors in a commercial building: suite entries, server and records rooms, warehouse man-doors, and shared lobbies where several tenants need different credentials. If keys get copied and former employees still hold one, this is the scope.

Two nearby pages overlap. Alarm and access control is the broader page, covering intrusion sensors and keypads for homes and small businesses; for a single storefront with one reader, start there. A video intercom at a front entry with no credential system behind it has its own page. And if the question is seeing rather than controlling, camera and CCTV installation is a separate scope, though the two are often wired in the same pull.

What the work involves

What a controlled door actually requires

Every controlled opening is a small system with five parts.

  • Credential reader. Proximity card, card-plus-mobile, or keypad. Exterior readers need an outdoor rating; Wasatch Front winters and high-elevation sun are hard on a reader meant for a lobby.
  • Electrified hardware. An electric strike in the frame, an electrified lock or panic bar in the door, or a maglock at the head. Hollow-metal doors take strikes well; aluminum storefront doors usually want electrified panic hardware or a maglock; wood doors need frame reinforcement first.
  • Door position switch and request-to-exit. The switch confirms the door closed. The REX sensor tells the controller someone is leaving legitimately, so the forced-door alarm stays quiet.
  • Controller and power. Controllers live in the IT closet, fed by a supervised power supply with battery backup. Each door gets one composite cable (reader, lock, switch, REX) back to that panel, plus the 120V circuit a licensed electrician brings to the supply.
  • Software and credentials. On-premises or cloud platform, with schedules by door and by person.

Door prep is where projects go sideways: strikes need the frame cut and reinforced, electrified locks need a power-transfer hinge, panic bars need a door rated for them. We get the hardware supplier and the cabling plan agreeing before frames are set. Grandview holds the contract and manages licensed low-voltage and electrical trade partners; we sequence, inspect, and quality-check every door before the system goes live.

Architectural floor plan used to build the door schedule and reader locations for a commercial access control system
Egress and fire safety

How the locks and the fire alarm have to get along

A controlled door still has to let people out. Current Utah-adopted code treats free egress on any exit-path door as non-negotiable: one motion, no key, no card, no special knowledge. That shapes the hardware. Maglocks fail safe, releasing when power drops, and must also release on fire-alarm activation through a relay to the fire alarm panel. Electric strikes and electrified panic bars keep mechanical free egress and can be fail-secure, staying locked to outsiders during an outage.

Delayed-egress hardware, which holds a loading-dock door briefly while an alarm sounds, is allowed only in specific occupancies with specific signage, so we route that question through the fire marshal early. Provo, Orem, and Salt Lake City run predictable fire-marshal reviews; fast-growth Lehi and Saratoga Springs can queue differently, and the schedule reflects that.

A reader mounted too high, or a controlled door on an accessible route with no automatic operator, creates a barrier the ADA does not allow. Where an operator is in the scope, it ties into the same controller so one credential both releases and opens the door; our accessibility retrofit work often runs alongside.

Sequence

How the access control scope fits a build-out

  1. Door schedule and credential plan. Which openings get controlled, who gets in, when, and what happens during a power loss. One page that prevents most change orders.
  2. Hardware specification. Each door gets its strike, lock, or maglock matched to the door and frame material.
  3. Rough-in with the electrical. Composite cable and conduit go in while walls are open, alongside the commercial electrical fit-out. Frames get prepped before they are set.
  4. Trim, program, test. Readers and hardware go on after paint. Every door is tested for lock, release, forced-door alarm, and fire-alarm release.
  5. Handover. Credentials loaded, administrators trained, as-built door schedule handed over.

This scope usually rides inside a tenant improvement or commercial renovation, coordinated under the MEP and systems umbrella; standalone retrofits are welcome too.

Commercial building hallway with handrails and escalators, a shared circulation path where controlled doors must still allow free egress
Budget

What commercial access control costs in Utah County

As a ballpark planning number, not a quote, a wired door with reader, electric strike, position switch, REX, cabling, and its share of a controller typically lands around $2,000 to $4,500 per opening in Utah County during open-wall construction. Doors needing a maglock with fire-alarm interface, an electrified panic bar, or an automatic operator often run $4,500 to $8,000. Controller and software are a shared base cost, so the per-door number drops as the count rises.

What moves the price: door and frame material (aluminum storefront is the most expensive to electrify), retrofit versus open walls, distance from the IT closet, and whether an operator or intercom is part of the opening. We price it as line items per door.

Questions we actually get

Do you install the access control system yourselves?

No, and we say so plainly. Utah requires low-voltage and electrical work to be performed by licensed specialty contractors. Grandview holds the contract, brings in licensed low-voltage and electrical trade partners, and coordinates, sequences, and quality-checks their work inside your project. Every license, ours included, is verifiable at dopl.utah.gov.

Can a maglock be used on an exit door?

Only with safeguards. A maglock on an egress door must release on loss of power, on fire-alarm activation, and typically on a motion sensor or push-to-exit button on the egress side. Many jurisdictions prefer an electric strike or electrified panic bar because free egress stays mechanical. We confirm with the fire marshal before ordering hardware.

Does a commercial access control installation need a permit in Utah?

Usually yes. The 120V power to the controller is electrical work, and any lock tied to the fire alarm or affecting an exit door draws fire-marshal review under current Utah-adopted code. We pull the permits as part of the scope and verify local specifics with the city building department.

Can the system be added to an existing building without opening walls?

Yes, and most retrofits are. Cabling gets fished through ceilings and plenums, with surface raceway where there is no path. Hollow-metal frames usually accept a strike; wood or aluminum doors may need new hardware. Expect roughly 20 to 40 percent more labor per door than an open-wall install.

Tell us what you’re working on

We reply within a couple of hours during business hours — a day at most. You’ll get a straight read on scope, sequence, and budget before anyone commits to anything.

Request an estimate   (385) 236-1741