Renovation & Build-Outs · Flooring

Sheet vinyl flooring in Utah County

Sheet vinyl is resilient flooring that comes off a 6- or 12-foot roll and goes down as one continuous piece, so a laundry room, bathroom, or rental kitchen gets a floor with no joints for water to find. Grandview Contractors installs it across Utah County and Salt Lake County under a Utah DOPL B100 general contractor license, usually within a larger remodel or unit turn.

Discuss a project   Or call (385) 236-1741

Bright empty room with newly installed wood-look flooring in a Utah County home, ready for baseboard
Right fit

When sheet vinyl is the better call than plank or tile

Sheet vinyl loses the beauty contest to luxury vinyl plank and luxury vinyl tile, and wins almost everything else in a wet room. Plank and tile floors have hundreds of joints; a 12-foot roll in a typical laundry or bathroom has none, so when a washer hose lets go the water stays on top.

It’s the right choice for laundry and utility rooms, half baths, mudrooms, basement bathrooms on a slab, and rental kitchens where the turnover budget has to cover the floor and the paint. It’s the wrong choice for a showcase main floor, for rooms wider than 12 feet where a seam would cross the view, and for anyone who wants to replace one damaged board later. There, plank is the better product; our glue-down vs floating vinyl page covers how to install it. If the room is dry and budget is the driver, laminate is worth a look too.

The work

What a sheet vinyl installation actually involves

Two product families, two different installs. Felt-backed sheet vinyl gets a full spread of adhesive and bonds permanently. Fiberglass-backed sheet vinyl lies flat on its own and can go down loose-lay or with perimeter and seam adhesive only, which makes it the usual pick for rentals where the floor will be replaced again in eight years.

  1. Substrate. Sheet goods telegraph everything: a nail head, a plywood seam, the grout lines of an old tile floor all show through within a season. Over a wood subfloor we install new 1/4-inch underlayment-grade plywood, fill and sand every seam and fastener, and prime. Over a well-bonded old sheet floor, an embossing leveler skim-coat can save the tear-out. Over a basement slab, we moisture-test first; slabs along the Wasatch Front sit on soils that wick water upward, which is what loosens adhesive from below. Heavier correction is its own line item under subfloor prep and leveling.
  2. Acclimate. Vinyl rolled tight in a cold truck holds its curl. In a Utah January we unroll it inside at room temperature for a day before cutting.
  3. Template and cut. Rooms with toilets, floor drains, and appliance alcoves are templated with a felt pattern, then transferred to the sheet and cut in one go. That’s how the cut around a toilet flange ends up tight instead of caulked.
  4. Seams and edges. Where a seam is unavoidable, we double-cut it along a pattern line, seal it, and roll the whole floor with a 100-pound roller. In laundry rooms and commercial restrooms, the sheet can run up the wall a few inches over a cove stick for a flash-coved sanitary base, the detail that keeps a leak on the floor.
  5. Finish. Base shoe or vinyl cove base, transitions, and appliances set back on sliders rather than dragged.
Floor prep tools, screws, and filler laid out on a subfloor before a resilient flooring installation
Basement utility and storage area with a hard-surface floor, the kind of below-grade room sheet vinyl suits well
Budget

What does sheet vinyl flooring cost in Utah?

As ballpark planning numbers, most residential sheet vinyl installs in Utah County land between roughly $3 and $7 per square foot installed, with the material usually the smaller half of that. Treat the range as a budgeting tool, not a quote. What moves the number is under the vinyl: new underlayment plywood can add roughly $1.50 to $3 per square foot, and a slab that fails a moisture test needs mitigation before any adhesive goes down.

Other drivers: product grade (a thin rental floor versus a 20-mil-plus wear layer for a commercial kitchen), room geometry (every closet and alcove is template time), flash coving and heat-welded seams, and what’s coming out. One flag on that last item: sheet vinyl and the black mastic under it in homes built before the early 1980s can contain asbestos, and a lot of Provo, Orem, and Salt Lake housing stock is that age. We have suspect material tested before anyone scrapes it, following EPA guidance on asbestos in homes. Standard tear-out is priced through our floor removal scope; abatement, when needed, is a separate licensed trade we coordinate.

For owners replacing floors in volume, sheet vinyl gets cheaper per unit as the count goes up; see our apartment unit turn programs.

Questions we actually get

Can you install sheet vinyl over my existing vinyl floor?

Often, yes. If the old sheet is a single layer, fully bonded, and not cushioned, we skim it with an embossing leveler so the old pattern can’t telegraph through, then install over it. Two existing layers, loose spots, or a cushioned back mean tear-out. We check the layers at a register or threshold before pricing.

Is sheet vinyl really waterproof on a basement slab?

The vinyl is. The adhesive isn’t, and water on a Utah slab comes from below. Felt-backed sheet glued over a damp slab bubbles and releases within a year. We test the slab first and use a loose-lay fiberglass product or a moisture-tolerant adhesive where the numbers call for it.

What happens in a room wider than 12 feet?

There will be a seam, and the job is to make it disappear. We plan it along a pattern line away from the doorway and the sink, double-cut both sheets together for a hairline joint, then chemically seal it. In commercial restrooms and break rooms we heat-weld seams instead, fusing them into one surface.

My laundry room floor is from the 1970s. Can you just pull it up?

Not until it’s tested. Older sheet flooring, its backing, and the black adhesive beneath it frequently contain asbestos, and scraping it releases fibers. A lab sample takes a few days. If it comes back positive, the safe and often cheaper route is encapsulating it under new underlayment rather than removing it. We’ll price both options.

Where this fits

Sheet vinyl is one of the resilient options in our flooring installation services, part of our wider renovation and build-out work, and every project runs under one B100 general contractor license you can verify at dopl.utah.gov.

Tell us what you’re working on

We reply within a couple of hours during business hours — a day at most. You’ll get a straight read on scope, sequence, and budget before anyone commits to anything.

Request an estimate   (385) 236-1741