Fire-Rated Drywall Assemblies in Salt Lake City
A fire-rated drywall assembly is a wall or ceiling built to a tested design — specific board, layers, fastener spacing, and sealed penetrations — that holds back fire for a listed one or two hours. Grandview Contractors builds rated garage separations, unit demising walls, and commercial corridor and tenant separations in Salt Lake City and Utah County under a B100 license, inspected before cover.

When the rating is the scope, not just the board
Plenty of walls get 5/8-inch Type X because it’s on the truck. That doesn’t make them fire-rated. A rating belongs to the whole assembly — framing, board, layers, screws, joints, and every pipe and box through it — and the inspector checks the assembly, not the sheet. This page covers garage-to-house separations, ADU conversions, townhome and fourplex party walls, and commercial corridor and demising walls. The broader trade lives on our drywall page.
Unrated office framing belongs under metal stud and drywall partitions. If the goal is quiet rather than fire, soundproof drywall is the fit — though most demising walls need both. Plain new board is drywall installation; an open garage that needs insulation before a rated lid is an insulation and drywall package.
What a one-hour or two-hour assembly requires
Rated assemblies follow tested designs — UL listings and the Gypsum Association’s Fire Resistance Design Manual are what inspectors recognize. We build to the design the plans name, or propose one and get it approved first.
- Board. Type X is 5/8-inch gypsum with glass-fiber reinforcement that holds the core together as it calcines. Type C is the shrink-compensated version most one-hour ceiling designs require — substituting X on a ceiling voids the listing.
- Layers. One-hour walls are usually one layer per side; two-hour walls stack two with staggered joints, and only the face layer gets taped and filled.
- Fastener schedule. Screw spacing is tighter than standard hanging and is part of the listing. Where the wall is also a seismic shear wall — common along the Wasatch fault — both schedules have to be met and both get inspected.
- Penetrations. Every pipe, duct, and outlet box needs a listed firestop system — intumescent sealant, collars, putty pads — and back-to-back boxes get offset. This is where most failed inspections come from.
- Continuity. A rated wall runs from slab to the rated deck, not to the dropped ceiling, with a listed head-of-wall joint that allows for deflection on steel buildings.

Where rated walls show up along the Wasatch Front
The attached garage is the common residential case. Under current Utah-adopted code, the garage-to-house wall carries gypsum board on the garage side, and a garage ceiling with living space above carries 5/8-inch Type X — the International Residential Code is the base document Utah adopts and amends. Salt Lake City’s ADU ordinance and garage conversions across Provo, Orem, and Lehi have made that separation a frequent standalone job: a garage conversion ADU rarely passes without rebuilding it, and a legalized basement unit usually needs a rated ceiling and door at the shared stair.
Multifamily is the second case — townhome party walls and duplex-to-fourplex separations, where HOA-dense developments in Saratoga Springs and Eagle Mountain often want the assembly detail submitted with the permit. Commercial build-outs are the third: corridor, demising, and mechanical-room walls inside a tenant improvement. Rated doors and self-closing hardware at garage and corridor openings are part of the same scope. One sequencing note: fast-growth Lehi and Saratoga Springs can queue longer for inspections than Salt Lake City or Provo, so we book the open-wall inspection when framing starts, not when the finishers are waiting. We see dependencies before they become delays.
From listed design to signed inspection card
- Confirm the rating. One hour or two, plus any sound or shear requirement. When it’s a judgment call, we verify with the city building department before pricing.
- Pick the listed design. Framing, board, and layer count matched to a UL or GA design, with the design number on the job for the inspector.
- Rough-in and firestop. Licensed electricians, plumbers, and HVAC trades — we hold the contract and coordinate their work — run through the wall first, and every penetration is firestopped before board is hung.
- Hang to the schedule. Listed fastener spacing, staggered joints, continuity to the deck. We photograph fastener patterns and firestops before cover.
- Inspect, then finish. The city sees the assembly before joints are closed. Then face-layer taping, fastener heads, head-of-wall joints, and the finish level the room demands.

What moves the cost of a fire-rated wall
Layer count first: a two-hour double-layer wall roughly doubles board and hanging labor. Penetration count second — each pipe, duct, and box is a priced firestop item, so a demising wall full of outlets costs more than a blank one. Rated door packages and whether the wall is open or must be demolished back to framing move the number too.
As ballpark planning numbers, not a quote: a single-layer one-hour wall hung and finished in Salt Lake City typically runs $3.00–$5.00 per square foot of board, with two-hour assemblies, ceilings, and heavy firestopping higher and rated doors priced per opening. Rated walls usually sit inside a basement finish, an ADU, or a tenant improvement — see our renovation and build-outs hub. We give a real number after seeing the wall and the plans; verify our license at dopl.utah.gov.
Questions we actually get
Is 5/8-inch Type X drywall by itself a one-hour fire rating?
No. The rating belongs to a tested assembly, not the board. A one-hour wall needs the listed framing, board, fastener spacing, finished joints, and firestopped penetrations together. Type X at standard screw spacing with unprotected outlet boxes will not pass inspection.
Does my garage conversion need a fire-rated wall or ceiling?
Almost always. Converting an attached garage, or finishing it under existing bedrooms, requires a rated separation from any remaining garage and often a rated ceiling and self-closing door. Salt Lake City, Provo, and Orem each inspect it before cover; we confirm the exact requirement with your building department before pricing.
Can a wall be both fire-rated and soundproof?
Yes, and most unit demising walls are. Many listed designs carry both a fire rating and a tested STC rating — staggered-stud framing, cavity insulation, and double layers of Type X do both jobs. We satisfy the fire requirement first, then confirm the sound rating on the same listing.
What if the wall is already covered and was never inspected?
The inspector can require it opened. For a conversion or ADU legalization, that usually means cutting inspection ports or pulling board to verify fastener spacing and firestopping. We price that open-and-verify work up front rather than guessing.
Tell us what you’re working on
We reply within a couple of hours during business hours — a day at most. You’ll get a straight read on scope, sequence, and budget before anyone commits to anything.