Commercial Metal Stud & Drywall Partitions in Salt Lake City
Metal stud and drywall partitions are the non-load-bearing steel-framed walls that divide a commercial floor plate into offices, suites, corridors, and demising lines. Grandview Contractors lays them out from the plans, frames them in light-gauge steel, and finishes them for occupancy across Salt Lake County and Utah County under a Utah DOPL B100 general contractor license.

When steel studs beat wood, and when a partition needs a different page
In commercial space, steel studs are the default for good reasons: they’re straight, they don’t shrink or twist as the building’s HVAC dries the air, they’re non-combustible, and they go up fast on a slab. Splitting an open office into private offices, carving a suite out of a vacant floor, building the demising wall between two tenants — this is that scope. It’s the backbone of most office build-outs and nearly every tenant improvement we run.
Two neighbors overlap. If the wall’s main job is a listed fire-resistance rating — a corridor, a demising wall the fire marshal will inspect — start with fire-rated drywall assemblies; the studs are still steel, but the assembly details drive everything. If the job is keeping a conference room private, soundproof drywall covers the acoustic layers. For walls in a house or a wood-framed remodel, plain drywall installation and finishing is the right page — steel studs rarely make sense there.
What goes into a commercial partition wall
A partition starts as a line snapped on the slab from the architect’s dimensions, checked against existing columns, window mullions, and ceiling grid before any track is shot down. Bottom track gets powder-actuated fasteners into the concrete; top track goes to the underside of the ceiling grid or all the way to the structural deck, depending on whether the wall is rated, acoustic, or secure, or simply a visual divider.
Stud gauge and width are the real spec decisions. Standard interior partitions use 3-5/8″ studs at 16″ or 24″ on center — 25-gauge for most office walls, 20-gauge where the wall is tall, carries casework, or holds a door frame that will slam a thousand times a year. Hollow-metal frames get 20-gauge jamb studs set in the framing, not cut in afterward. Flat-strap or plywood backing goes in for TV mounts, grab bars, and upper cabinets, because a screw into a bare 25-gauge stud holds very little.
Full-height walls get a slip track or deflection head so the structure above can move without crushing the wall below. Along the Wasatch Front that isn’t a formality: current Utah-adopted code treats partition bracing and anchorage as a seismic item, so tall partitions are braced back to structure at intervals rather than leaning on the ceiling grid. The USGS earthquake hazards program explains why Salt Lake County’s seismic design category is what it is.

Electrical, data, and plumbing live inside these walls. Grandview holds the contract and sequences licensed electricians and plumbers for the rough-in between framing and board — see MEP coordination.
Sequence from layout to paint-ready
- Layout and field verification. Plan dimensions against the as-built floor; column wraps and mullion alignments get resolved here, not mid-framing.
- Track and stud. Bottom track to slab, top track to grid or deck, studs plumbed and crimped or screwed. Door and window openings framed with headers and jamb studs sized to the frame.
- In-wall rough-in and inspection. Licensed electricians and plumbers we coordinate run their work inside the open framing. Blocking goes in. Salt Lake City and most county jurisdictions want a framing and rough-in inspection before cover, so we schedule it and don’t board over anything until it’s signed.
- Board, tape, and finish. 5/8″ board is the commercial standard, screwed at spec spacing with fine-thread screws for steel. Tape and three coats of compound, with a Level 5 skim where the walls will take sheen paint or wash lighting.
- Handoff. Sanded, primed, and ready for paint, base, and door hardware. We see dependencies before they become delays.

What drives the cost of metal stud partitions in Salt Lake City
Wall height is the biggest mover: a partition stopped at a 9-foot grid is a very different wall from one running 14 feet to the deck with a deflection head and bracing. Gauge is second. Then door frames (each is layout, jamb studs, a header, and a hung door), the count of corners and short jogs, and whether the space is occupied, which adds dust walls and after-hours work.
As ballpark planning numbers — not a quote — framed, boarded, and finished metal stud partitions in Salt Lake County commonly land in the $10–$20 per square foot of wall range for ceiling-height office walls, with full-height, rated, or acoustic walls running higher. Permits move the schedule more than the price: Salt Lake City’s established commercial review is predictable, while fast-growing Lehi and Saratoga Springs can queue longer. Verify our license at dopl.utah.gov before anyone commits to a number.
Questions we actually get
Should my partition walls go to the ceiling grid or to the deck?
Go to the deck when the wall needs a fire rating, real sound separation, or security — a grid-height wall leaves an open plenum above it. Plain office walls can stop at the grid, which is faster and cheaper. Decide before layout; deck-height walls need a deflection head and bracing.
Does a metal stud partition need a permit in Salt Lake City?
Almost always, yes — new interior walls in commercial space change egress paths and usually involve electrical, so they fall under a tenant-improvement permit with framing and rough-in inspections before cover. We pull the permit and schedule inspections as part of the scope; unusual projects get confirmed with Salt Lake City building services first.
Can you build partitions while the office stays open?
Yes. We set temporary dust walls, work in phases, and run noisy cutting and powder-actuated fastening after hours when the lease or the neighbors require it. It costs more than a vacant floor and takes longer, but it’s routine for us.
Why 20-gauge studs instead of 25-gauge?
Use 20-gauge where the wall is tall, carries a hollow-metal door frame, supports heavy casework or wall-mounted equipment, or takes a beating in a corridor. 25-gauge is fine for most ceiling-height office walls. Mixing both on one job — heavier studs only where they earn their cost — is normal.
Related services
Partitions are one piece of the drywall work we do and usually sit inside a larger renovation or build-out. If you’re planning a full suite — walls, ceilings, electrical, flooring, paint — tell us the whole scope and we’ll sequence it at once.
Tell us what you’re working on
We reply within a couple of hours during business hours — a day at most. You’ll get a straight read on scope, sequence, and budget before anyone commits to anything.