Site, structure & envelope

Composite siding installation

Composite siding is a fully synthetic board — cellular PVC or a polymer-and-mineral blend — with color through its whole thickness, so it never needs paint and a scratch doesn’t show primer. Grandview installs composite lap and board-and-batten across the Salt Lake Valley and Utah County under a B100 general contractor license, gapped and fastened for a material that moves with temperature more than wood or cement.

Discuss a project   Or call (385) 236-1741

Contemporary two-story home with clean, paint-free synthetic lap siding under a clear Utah sky

When composite is the right board, and when a sibling is

Composite earns its premium when you want the thick shadow line of a painted wall but refuse to own a paint cycle. Along the Wasatch Front, sun-facing walls want recoating years before shaded ones, because UV at 4,500 feet is measurably stronger than at sea level. A color-through board has no film to chalk or peel; the pigment on day one is the pigment at the core.

It also suits owners who like the no-paint logic of vinyl lap siding but not the look. Composite boards are several times thicker than a vinyl panel, lie flat without vinyl’s ripple in low afternoon light, and take a snow shovel or a July hailstone without cracking.

Choose something else in two cases. If you want a repaintable surface at a lower price, fiber cement lap siding is the proven value pick. If you want real wood grain depth and plan to paint anyway, LP SmartSide engineered wood costs less per square. Composite is the sibling for the color you want to keep and never touch again.

What’s actually in a composite board

The name covers two materials that install differently. Cellular PVC is a foamed vinyl core under a dense skin, the same chemistry as premium PVC trim: light, cuts like pine, and solvent-welds at butt joints for a continuous line. Polymer-mineral composite blends resin with crushed stone filler, extruded as an interlocking lap profile: heavier, stiffer, more impact-resistant, joined by concealed interlock rather than adhesive.

Both share the trait that governs the installation: thermal movement. A 16-foot composite board changes length noticeably between a January morning and an August afternoon, and the Salt Lake Valley routinely sees a hundred-degree spread between the two. Manufacturers publish gap charts tied to installation-day temperature, and the crew follows them with a thermometer on the wall. Boards hung tight on a cold day buckle in summer; boards hung tight on a hot day open gaps in winter.

Color follows the same physics. Dark pigments absorb heat, so many composite lines restrict deep colors or require a heat-reflective formulation on south and west walls. We check the approved palette for your orientation before a sample goes to HOA review, usually the first gate in newer Lehi, Herriman, and Eagle Mountain developments.

Close-up of lap siding courses and roofline trim on a Utah home, showing the shadow line a thick board produces

What a composite siding installation involves

Composite is forgiving about water and strict about fastening. The manufacturer’s rules are the contract.

  1. Dry in and flatten. Weather-resistive barrier, flashing at openings and roof-to-wall. Rigid composite telegraphs any bow in the sheathing, so we shim the wall flat first.
  2. Read the temperature. The reading at the wall sets the end gap for every board hung that day, logged on the job sheet.
  3. Fasten into framing. Stainless or hot-dip galvanized fasteners through the manufacturer’s slot into a stud, snug but never pinched. A pinched fastener locks the board and causes the oil-canning that gives synthetic siding a bad name. Canyon-wind corridors get high-wind spacing.
  4. Join by the material. PVC butt joints get solvent-welded or backed with a joint plate; polymer-mineral lap locks course over course and ends at a proprietary joint cover.
  5. Trim in kind. Corners and casings come from matching composite trim so the whole exterior moves together; wood trim on composite siding is how corners crack by year three. trim and corner detailing is specified with the field boards, not after.
  6. Seal only where needed. Composite relies on gaps and covers for movement, not caulk; the few joints at penetrations get a high-movement sealant rated for the material.

All of this is carpentry we perform under our Utah DOPL-verifiable B100 license. Relocating an exterior light or service penetration is done by licensed electricians; Grandview holds the contract, sequences their work, and checks it before the wall closes.

What does composite siding cost in Salt Lake City?

As ballpark planning numbers only: composite siding along the Wasatch Front typically runs about $12–18 per square foot installed, including tear-off, weather-resistive barrier, flashing, and matching composite trim. A typical two-story home lands between roughly $32,000 and $55,000, the top material tier on our siding menu, traded against never buying paint again. Ranges to plan with, not quotes; a firm estimate follows a site walk and a written scope.

  • PVC versus polymer-mineral. Mineral composites carry more material cost; PVC carries more labor at the joints.
  • Trim package. Matching composite corners and casings cost more than primed stock because every piece is a finished product.
  • Color and exposure. Heat-reflective dark colors cost more and are often special-order with lead time.
  • Wall flatness and height. Wavy old sheathing and three-story walls both add time before the first board goes up.
  • Discovery allowance. Sheathing repair gets a line up front, so rot found at tear-off is priced against a number you already approved.
Modern minimalist home exterior with flat, uniform synthetic cladding and clean corner lines

Questions we actually get

Does composite siding fade in Utah’s sun?

Slowly and evenly, which is the point. Color runs through the board and the resin carries UV stabilizers, so there is no paint film to chalk or peel on south and west walls. Light and mid-tone colors hold best; deep colors should come from a manufacturer-approved heat-reflective line.

Can composite siding be installed in winter?

Yes, and in one way it’s easier: there is no paint or primer with a minimum temperature. The constraint is the gap chart. Boards hung at 20°F need the widest end gaps the manufacturer allows so they can grow in August. PVC solvent welds have their own minimum temperature, which we schedule around.

Can composite go over my existing siding?

Rarely, and we usually advise against it. Composite is rigid and shows every ripple beneath it, and its fasteners must reach framing through the full stack. Tear-off also lets us inspect and re-flash the wall, which is what keeps it dry. If wind or hail is what took the old cladding off, storm damage siding repair covers the insurance-coordinated version of this scope.

Is composite the same as engineered wood or fiber cement?

No. Engineered wood is wood strand and resin that must be painted; fiber cement is cement and cellulose, painted or factory-coated. Composite contains no wood fiber and no cement, and its color is part of the material. If a salesperson calls fiber cement “composite,” ask whether the board ever needs paint. The rest of the shell lives under site, structure & envelope.

Tell us what your walls are doing

Send photos of the sunniest wall and the color you have in mind. We reply within a couple of hours during business hours, a day at most, with a straight read on whether composite fits, which chemistry suits your exposure, and a realistic budget range before anyone commits to anything.

Request an estimate   (385) 236-1741