Brick patio installation in Utah County
A brick patio is fired clay paving brick laid in a bond pattern over a compacted base or a mortar bed, the right pick when you want color that’s baked in rather than painted on. Grandview designs and installs brick patios across Utah County and Salt Lake County under a Utah B100 general contractor license.

When brick is the right patio material
Brick earns its place on three kinds of projects: a home with existing brick where a matching patio ties the yard to the house; a traditional design where the tight 4-by-8 module reads correctly; and any patio where long-term color matters. Clay brick is fired, not pigmented, so it doesn’t fade the way concrete pavers do under Utah’s high-elevation UV.
It isn’t always the answer. A concrete paver patio gives you bigger formats and a lower price per square foot. A flagstone patio is the choice for irregular, organic stone instead of a repeating grid. A gravel patio wins on budget and drainage when you don’t need a hard, furniture-friendly surface. Brick sits between them: more formal than flagstone, warmer than pavers.
Sand-set or mortar-set: the first decision
Every brick patio is one of two systems, and the choice drives everything after it.
Sand-set (flexible). Brick on a one-inch sand bedding over compacted road base, with sand-filled joints and a restrained edge. The surface flexes with the ground, and a settled brick can be lifted and re-bedded. It’s our default for Utah County, where roughly a hundred freeze–thaw days a year will find any rigid weakness.
Mortar-set (rigid). Brick bedded in mortar on a reinforced concrete slab with mortared joints. Crisp and immovable, but only when the slab has control joints and a drained, compacted subgrade. It’s the right call when the patio ties into mortared brick steps or seat walls, or when thin paver brick goes over an existing sound slab.
Either way, we specify paving brick rated for severe weathering under ASTM C902 (Class SX), whose low absorption keeps it from spalling after a wet freeze. The Brick Industry Association publishes the technical notes we design to.
How we build a brick patio that stays flat
- Set the grade. Finish elevation is set against the door threshold and sloped a quarter inch per foot away from the house. On the expansive clay and collapsible bench soils the Utah Geological Survey maps across much of the valley, we excavate deeper and add a geotextile layer under the base.
- Build the base. Six to eight inches of three-quarter-inch road base, compacted in lifts. For a sand-set patio this base is the structure; the brick is the wearing surface.
- Screed the bedding. One inch of coarse concrete sand, screeded to grade and never pre-compacted. For mortar-set, this step becomes a slab pour and cure.
- Lay the bond. Joints held at about an eighth of an inch. Clay brick varies in size more than concrete pavers, so we pull from several cubes at once to blend color and keep the pattern from drifting.
- Restrain the edge. Spiked edging, a concrete toe, or a mortared soldier course. Without it, the sand migrates and the outer rows roll out within a couple of seasons.
- Compact and joint. The field is vibrated with a padded plate, joints swept with polymeric sand and misted to set.

Pattern, bond, and border choices
Pattern is a structural choice as much as a visual one.
- Herringbone (45 or 90 degrees) locks every brick against its neighbors in two directions. It’s the strongest bond and our recommendation anywhere a grill or wheeled traffic will run. It also produces the most cuts.
- Running bond is fastest to lay and forgiving on a long, narrow patio, but rows can creep along their length without sound edge restraint.
- Basketweave only works with true 2:1 modular paving brick, where two bricks side by side equal one brick long. Many wall bricks miss that ratio, one more reason we don’t build patios from them.
- Soldier or sailor border frames the field, hides the cut edge, and doubles as edge restraint when mortared.
A common request is reclaimed brick from a demolished building. Most salvaged brick was made for walls, absorbs water freely, and will flake apart in a Utah winter. If the old look matters, tumbled new paving brick gets you there with a surface that survives.
What does a brick patio cost in Utah County?
As a ballpark planning number, a sand-set brick patio in Utah County commonly runs $22 to $40 per square foot installed; mortar-set over a new concrete slab runs $35 to $55 or more. Brick typically lands above concrete pavers and below cut natural stone. We give a firm estimate after a site walk and a set design.
What moves the number: the system (a slab roughly doubles the base cost), pattern (herringbone adds labor through cuts), brick grade, excavation depth on poor soils, and access, since a patio wheelbarrowed through a side gate costs more than one a skid steer can reach. Mortared brick steps or a matching brick fire pit are priced as their own line items.

Questions we actually get
Will a brick patio heave or crack in Utah winters?
A sand-set brick patio on a properly compacted base moves slightly and settles back, which is the point of a flexible system. Heaving comes from a shallow base, no geotextile over clay, or standing water. Mortar-set brick cracks only when the slab under it wasn’t jointed and drained.
Why is there white powder on my new brick patio?
That’s efflorescence: soluble salts carried to the surface as the brick and bedding dry out. It’s cosmetic, common in the first year, and brushes off with a stiff broom and water. It isn’t a defect in the brick or the install, and it fades as the patio weathers.
Can you lay brick over my existing concrete patio?
Yes, if the slab is sound, drains, and sits low enough that adding brick doesn’t bury the door threshold. We use thin paving brick set in mortar over the slab. If the slab is cracked or heaved, it’s usually cheaper to remove it and build a sand-set patio on fresh base.
Should I seal a brick patio?
Not for durability. Clay brick’s fired surface handles Utah UV and freeze–thaw on its own, so sweeping and rinsing is the maintenance. A breathable sealer is optional for stain resistance around a grill or dining area. Avoid film-forming sealers, which trap moisture and can cloud under a freeze.
Where this fits
Brick patios are one patio option within our landscaping and hardscaping services, part of the site, structure and envelope family.
Tell us what you’re working on
We reply within a couple of hours during business hours, a day at most. You’ll get a straight read on scope, sequence, and budget before anyone commits to anything.