Downspout installation & extensions in Utah County
Downspout installation decides where roof water actually ends up: new drops cut into existing gutters, 2×3 drops upsized to 3×4, and extensions or buried lines that carry discharge past the foundation backfill. Grandview installs and extends downspouts across Utah County and Salt Lake County under a licensed and insured B100 general contractor.

When downspout work is the right scope, and when it isn’t
Most gutter complaints we hear are downspout problems wearing a gutter costume. One corner overflows in every storm; there’s a wet stripe on the basement wall under one drop; the splash block has been kicked aside by the mower for three summers. If the gutter is sound and pitched, you don’t need new gutters. You need more drops, bigger drops, or a discharge plan.
This is a stand-alone job when the gutters stay. If the runs are sagging or pulling off the fascia, start with gutter repair and re-hanging, because a re-pitched gutter moves the low points, and therefore the outlets. If the whole system is done, downspouts come bundled with seamless gutter installation and we size them together. If water is already in the basement, an extension is the first fix but rarely the last; that conversation continues on the French drain page.
The homes that need this most share a pattern: one drop per 40 or 50 feet of gutter, 2×3 downspouts on a roof that produces far more water than that, and a plastic splash block on backfill that slopes toward the house. The Utah Geological Survey maps expansive clay across the valley floor and collapsible soils on the benches. Both move when wet, and the backfill zone is exactly where a short downspout puts the water.
Sizing, placement, and the discharge end
Size. A 2×3 rectangular downspout drains roughly 600 square feet of roof in a steady rain; a 3×4 handles about twice that. We measure each drainage plane, count drops from roof area, then add margin for summer monsoon cloudbursts, when an inch can fall in under an hour and a 2×3 outlet can’t take it fast enough. On most Utah County homes we upsize to 3×4 by default. The larger outlet also passes the shingle grit and cottonwood fluff that chokes a 2×3 by August, and ices shut less readily through the freeze–thaw cycling that runs November into April.
Placement. New outlets are cut at the true low point, found with water rather than a level, since fascia is rarely straight. A drop goes near every inside corner where two runs meet, because that’s where flow doubles. Downspouts are strapped every eight to ten feet, at least two per story, screwed into framing or masonry anchors rather than siding alone.
Discharge. Every drop ends one of four ways: a rigid extension to a splash block six to ten feet out, a hinged extension that flips up for mowing, a buried 4-inch solid PVC line to a pop-up emitter or daylight, or a tie-in to an existing yard drain. We use solid pipe, not perforated, in the first ten feet from the house, with a cleanout at the base of the drop so a plugged line gets rodded instead of dug. Where grading slopes back toward the house, a longer extension helps, but regrading is the real fix.


How a downspout job runs
- Watch the water. We run a hose into each gutter and note where it overflows and where the discharge actually goes once it leaves the pipe.
- Count and size the drops. Roof area per plane and corner locations set the number and size of downspouts. Usually that means more drops and bigger ones, not a different gutter.
- Cut, hang, and strap. Outlets are cut and crimped into the existing gutter, sealed, and the downspout hung plumb with straps into solid backing. Old 2×3 holes are patched, not left as a second, smaller leak.
- Build the discharge. Extensions, buried lines, or drain tie-ins go in with the fall checked by water, and emitters placed where they won’t ice over a public sidewalk in January.
- Test under load. Hose in every gutter at full flow, and we watch each drop carry it away. Then we haul off the old material.
What does downspout installation cost in Utah?
A new aluminum downspout added to an existing gutter, with outlet, elbows, straps, and a surface extension, usually lands in the $150–$350 range per drop on a single-story home and somewhat more on a second story. Upsizing a 2×3 to a 3×4 is in the same neighborhood. Buried discharge lines are priced by the foot: a 15–25 foot solid PVC run to a pop-up emitter typically runs $400–$900 per downspout depending on soil, landscaping, and how much concrete or sod is in the way. These are ballpark planning numbers; a firm estimate follows a walk around the house.
What moves the number: drop count, story height, masonry anchors, rocky bench soils that fight a trencher, and whether a yard drain exists to tie into. For the foundation protection it buys, it’s routinely the least expensive line on an exterior estimate.
Questions we actually get
How many downspouts does my house need?
A workable rule is one downspout per 30 to 40 feet of gutter, and one 3×4 drop per 1,200 square feet of roof it serves. Long runs with a single drop at one end are the most common undersizing we find on Utah County tract homes. Inside corners where two roof planes converge almost always deserve their own drop.
Should I bury my downspout extensions or leave them on the surface?
Bury them if you can. A buried solid line with proper fall carries water farther, survives the mower, and doesn’t get kicked loose. The caveat is winter: pop-up emitters can freeze shut, so we set them where a frozen emitter backs water into the lawn rather than toward the house, and keep the first ten feet solid pipe.
Why does only one downspout overflow during storms?
Usually that drop serves an inside corner or the largest roof plane and is undersized, or the outlet is half-blocked with shingle grit and leaves. Sometimes the gutter has back-pitched toward that corner under years of snow load. We check all three before recommending a bigger drop, a second drop, or a re-hang.
Downspouts are one piece of the gutter installation and repair scope inside our site, structure & envelope work. The K-style or half-round profile feeding a drop affects how much water reaches the outlet; on flat and low-slope commercial buildings, drainage falls under commercial and box gutters. Our B100 license is verifiable at dopl.utah.gov.
Tell us what you’re working on
One overflowing corner or a whole house of short drops: we’ll give you a straight read on scope, sequence, and budget before anyone commits. We reply within a couple of hours during business hours, a day at most.