Site, structure & envelope

Seamless gutter installation in Salt Lake City

Seamless gutters are continuous aluminum runs roll-formed on site to the exact length of each fascia, so the only joints left are at corners, end caps, and downspout outlets. They’re the right choice for most Wasatch Front homes, and Grandview installs them across Salt Lake and Utah County under a licensed and insured B100 general contractor.

Discuss a project   Or call (385) 236-1741

Crew working along the eave of a brick house where a continuous seamless gutter run will be hung

When seamless is the right call, and when it isn’t

Pick seamless when you’re replacing a whole elevation or the whole house, when any straight run is longer than about twenty feet, or when the fascia faces the street and you’d rather not look at a splice every ten feet. On a 40-foot run that’s one continuous trough versus four sections and three slip joints, each asked to survive a Utah winter.

Pick sectional gutters instead when you’re patching one damaged length into a sound system or phasing work across a few budgets. “Seamless” describes how the gutter is made, not its shape: both K-style and half-round profiles can be formed as continuous runs, and the profile is a separate decision about capacity and the look of the house. If the material is the point rather than the joint count, copper and specialty gutters are their own conversation. And if your runs are sagging or leaking at a few seams but the metal is sound, start with gutter repair and re-hanging instead. This page is one scope within gutter installation and repair, part of the full shell under site, structure & envelope services.

The work

What a seamless gutter install actually involves

  1. Measure every run. Each fascia length is measured to the inch and the roof area draining into it is calculated. That area, not the length, decides 5-inch versus 6-inch gutter and the outlet count.
  2. Form on site. Aluminum coil feeds through a roll-forming machine at the truck and comes out as one piece, cut to the measured length. We spec .032-inch coil by default; .027 is cheaper, and it’s the gauge that gets crushed by a ladder or a slab of sliding snow.
  3. Hang and pitch. Hidden hangers screw through the gutter into the rafter tails, not just the fascia board, at 24 inches, tightened to 16 on bench lots and north-facing eaves that hold snow. Pitch is about a quarter inch per ten feet toward each outlet, checked with a level and then with water.
  4. Build the corners. The few joints a seamless system does have get the most attention: corners are strip-mitered on site or fitted with box miters, riveted, and sealed on the inside with a gutter-grade polyurethane. End caps get the same treatment.
  5. Cut outlets and connect. Outlets are cut and flanged into the trough, never surface-mounted, so there’s no lip to catch debris. Sizing and discharge are covered under downspout installation and extensions.
Power drill, bracket, and work gloves laid out before fastening hidden gutter hangers into rafter tails
Modern house exterior with long clean rooflines, the kind of straight fascia where continuous gutter runs look best

Why joint count matters more here than in milder climates

Every seam in a sectional gutter is a place where water sits, freezes, and pushes. The Wasatch Front sees well over a hundred freeze-thaw days a year, and ice inside a slip joint pries the sealant loose a little each cycle. By the third winter it drips into the backfill beside the foundation, and on the expansive clay and collapsible soils the Utah Geological Survey maps across both valleys, that slow wetting is what moves footings. A continuous run doesn’t give the ice a seam to work on.

Long aluminum runs have their own physics, though. Between a January night and a July afternoon, a sixty-foot run can change length by close to an inch. That’s fine when hangers let the gutter float and the corner sealant stays flexible, so we break very long elevations with an expansion joint rather than pinning one piece hard at both ends. We are fond of straight lines and straight answers, and the straight answer is that even seamless has a sensible maximum.

Canyon-wind gusts at the mouths of the Wasatch canyons are the other reason we fasten into framing. A gutter screwed to fascia gone soft from years of overflow will pull loose in a gust and take the board with it. Rot found on the walk-around is priced as its own line before anything goes up, and often pairs with a roofing scope, since drip edge and gutter flashing interlock at the eave.

What do seamless gutters cost in Utah?

Installed seamless aluminum gutter in Salt Lake and Utah County typically runs about $8–$15 per linear foot: roughly $1,500–$3,000 for a single-story home with 150–200 feet of eave including downspouts, and $3,000–$5,000 for a two-story home with a complex roofline. Those are ballpark planning numbers; the firm estimate follows an actual measure.

What moves it: 6-inch over 5-inch adds a couple of dollars a foot and is usually worth it where long valleys feed one run. Heavier .032 coil adds a little. Second-story access adds labor. Custom colors add lead time more than cost. Fascia repair, gutter guards, and buried downspout drains are priced as separate lines. Our B100 license is verifiable at dopl.utah.gov, and the measure costs you nothing.

Questions we actually get

Are the corners on a seamless gutter actually seamless?

No. Corners, end caps, and downspout outlets are joints on every seamless system. The difference is that a typical house goes from thirty-odd joints to six or eight, and those few are riveted and sealed from the inside, where the sealant is protected from UV and ice.

Is 6-inch gutter worth it, or is 5-inch enough?

Five-inch K-style handles most single-family roofs. We move to 6-inch when a long run collects a large roof area, when two valleys dump into one short section, or on low-pitch roofs where water sheets off fast. A summer cloudburst that drops an inch in an hour is the test; a run that overflows then was undersized, not clogged.

Can a seamless gutter be repaired if one section gets damaged?

Yes. A crushed length can be cut out and a new section spliced in with a lap joint, leaving two seams in that run instead of none. It’s a repair, not a reason to replace the elevation. Damage at a corner or outlet is usually a re-seal.

Does my fascia need to be replaced first?

Only if it’s soft. Hangers need solid wood to bite into, and we check every foot before we hang anything. Sound fascia gets reused; rotted sections get cut out and replaced as their own line item, which is far cheaper than finding out when a run pulls loose under snow.

Tell us what you’re working on

We reply within a couple of hours during business hours, a day at most. You’ll get a straight read on scope, sequence, and budget before anyone commits to anything.

Request an estimate   (385) 236-1741