Gutter repair & re-hanging in Utah County
Gutter repair re-pitches, re-fastens, and reseals an existing gutter system so it drains again — sagging runs lifted back to grade, failed hangers replaced with screw-in brackets, seams resealed, rotted fascia fixed first. It’s the right call when the metal is sound but the attachment or pitch has failed, and Grandview performs it under a licensed and insured B100 general contractor.

When repair beats replacement
Most gutter failures along the Wasatch Front aren’t metal failures. The aluminum is fine. What fails is the hardware holding it to the house: spike-and-ferrule nails worked loose by freeze–thaw, hangers spaced too far apart to carry a winter’s worth of ice, or fascia that softened until nothing holds a fastener. If the trough is intact, re-hanging costs a fraction of a new system and gives the same result — water moving to the downspout instead of pooling mid-run.
Repair is the wrong answer when the metal is done. Corroded steel, aluminum split at the roll, several feet of crushed profile, or a sectional system leaking at every joint all argue for replacement, usually with seamless aluminum gutters formed on site. Where one elevation has failed, a sectional gutter run is the economical patch. If the gutters drain fine but water still lands beside the house, the problem is the outlet — see downspout installation and extensions.
A quick self-test after a storm: overflow in one spot means a sag or a clog; drips from behind the gutter mean fascia rot or a failed drip edge; overflow along the whole length means undersized gutters, which repair won’t fix.
Re-hang, re-pitch, reseal — in that order
- Diagnose the sag. A string line shows the fall toward the outlet. Properly hung gutters drop roughly a sixteenth to an eighth of an inch per foot; a run bellied below that holds standing water, which freezes, which bends it further.
- Probe the fascia. Every fastener location gets an awl. Soft board is cut out and replaced with primed fascia before any hanger goes back in — a bracket screwed into rot fails by spring.
- Replace the hangers. Spikes come out, screw-in hidden hangers go in — typically 24-inch centers, tighter at corners and under valleys where ice concentrates. A screw holds several times the pull-out load of a spike in the same wood.
- Re-pitch and re-set. The run is lifted back to line, high at the far end and low at the outlet, back edge tucked under the drip edge so water can’t get behind it. Miters and end caps are re-set square.
- Reseal and flush. Seams, end caps, outlets, and miters are cleaned to bare metal and resealed with a tripolymer or butyl gutter sealant rated for movement, not silicone. Then a hose, and we watch it leave through the downspout.

Why Utah gutters pull away from the house
Gutters are sized for the weight of water. What loads them here is ice. A five-inch K-style trough full of ice weighs several pounds per foot, and a snow slab sliding off a steep roof delivers that as a shove, not a steady pull. Bench lots above Provo and Draper carry heavier snow than the valley floor and shed it faster, which is why bench re-hangs often add snow guards or tighter hanger spacing.
Freeze–thaw does the slower damage. Water trapped in a bellied run freezes and expands a hundred-odd times a winter along the Wasatch Front, levering seams open and walking spikes out of the fascia a fraction of an inch at a time. Canyon-wind gusts add a third force: a run loose on three hangers rattles, and a rattling gutter loosens every remaining fastener. Once it dumps beside the house, the expansive clay and collapsible soils the Utah Geological Survey maps across both counties take over, and a deferred repair becomes a foundation conversation.
Repair is also where adjacent problems surface. Rotted fascia usually means a missing or kicked-out drip edge — that’s roof flashing repair — and new fascia wants paint before winter. We flag both rather than hanging a gutter on a problem; the rest of the shell lives under site, structure & envelope services.

What does gutter repair cost in Utah?
Most residential gutter repair visits land in the low hundreds of dollars — resealing seams, replacing a short run of hangers, or re-setting one sag on a single-story home. Re-hanging a full elevation with new hidden hangers typically runs a few hundred to around a thousand dollars depending on length, stories, and corners. Fascia replacement is the variable: a few feet is modest, a whole elevation of rotted board can double the job. These are ballpark planning numbers; the firm estimate comes after we walk the roofline and probe the fascia.
Price moves down with single-story straight runs, sound wood, and easy ladder access; up with second-story work over a walkout, steep roofs that need staging, rotted fascia, and added snow guards. Under tree cover, gutter guards keep the run you just re-pitched from clogging again. Our B100 license is verifiable at dopl.utah.gov, and if the honest answer is that your gutters are at the end, we’ll say so and price a replacement through the gutter installation and repair scope instead.
Questions we actually get
Can you re-hang gutters without replacing them?
Yes, if the trough is straight and the metal is sound. We pull the old spikes, repair any soft fascia, install screw-in hidden hangers at tighter spacing, re-pitch the run toward the outlet, and reseal seams and end caps. Crushed, split, or corroded aluminum is the exception; that gets replaced.
What if the fascia behind the gutter is rotted?
The fascia has to be fixed first. We cut out soft board back to solid wood, replace it with primed fascia, and only then hang the gutter. Rot means water has been getting behind the gutter for years, so we check the drip edge too. Skipping this step is why some repairs fail the next winter.
Will new hangers stop my gutters from pulling off under snow?
Usually. Screw-in hidden hangers at 24-inch spacing, tighter under valleys and on bench lots, hold far more than spike-and-ferrule nails. On steep metal roofs that dump snow in one slab, we may also recommend snow guards along the eave, because no hanger is rated for a roof’s worth of ice arriving at once.
Can gutter repair be done in winter?
Re-hanging and hanger replacement happen year-round as long as the roof edge is safe to work from. Sealant is the limit: it needs moderate temperatures to cure, so in a cold snap we reseal during the warm part of the day or return for that step. Ice-filled gutters have to thaw before they can be re-pitched.
Tell us what you’re working on
A sagging run, a dripping seam, or an elevation that came down with the snow — you’ll get a straight read on repair versus replacement, and a budget, before anyone commits to anything. We reply within a couple of hours during business hours, a day at most.