Driveway Gates in Utah County
A driveway gate is the vehicle entry to a property: a single swing, double swing, or slide gate wide enough for a truck or trailer, hung on posts sized for the leaf weight and the wind. Grandview designs and installs driveway gates for homes, acreage, and commercial yards across Utah County and Salt Lake County under a B100 general contractor license.

When a driveway gate is the right call
You need a driveway gate when the opening has to pass a vehicle. That is the whole design problem: a 12-to-20-foot clear opening, a leaf weighing several hundred pounds, and hardware cycled every time someone leaves. A pedestrian gate is a four-foot walk opening on one pair of hinges and shares none of those problems.
If the gate should open from the car, you’re looking at an automatic gate with an operator — this gate plus a motor, controls, and safety devices. If the gate is the architectural centerpiece of the entry, a custom steel gate built to a drawing is the step up from the standard frames described here.
Driveway gates fit any line on our fencing page. The fence sets the look; the gate’s structure is its own problem.
Single swing, double swing, or slide
- Single swing. One leaf, typically up to 12 feet. Fewest moving parts, but a long leaf levers hard on one hinge post, so that post gets bigger and deeper.
- Double swing. Two leaves meeting at center for 14-to-20-foot openings. Each leaf is half the weight, and a drop rod at center holds them closed. Needs a flat swing arc inside the property.
- Slide or cantilever. The gate rolls along the fence line instead of swinging. The right answer on sloped driveways, short approaches, and anywhere snow gets plowed into the swing path. A cantilever gate needs roughly half its opening width again in clear fence line for the tail.
Grade is the usual tiebreaker. A driveway that climbs from the street — common on east-bench lots in Provo, Orem, and Alpine — won’t let an in-swinging gate clear the pavement. That’s when we steer toward a slide gate or an out-swing set back from the sidewalk.
What building a driveway gate involves
- Measure the approach, not just the opening. Turning radius off the street, where the open leaf will stand, and the widest thing that has to get through. A gate that passes a sedan but not the boat trailer is a gate you’ll rebuild.
- Size and set the hinge posts. Hinge posts are heavy-wall steel tube, larger than the fence posts beside them, set in footings well below frost depth. Expansive clay along the Wasatch Front lifts shallow posts a little more each freeze–thaw cycle, and a quarter inch at grade becomes inches at the latch end of a 12-foot leaf. The Utah Geological Survey maps these soils; our footing follows what’s actually in the hole.
- Frame it to resist sag. Every swing gate wants to drop at the latch end. A welded steel frame with a diagonal brace from the bottom hinge corner to the top latch corner carries that load back to the post. Wood and vinyl gates get a steel sub-frame or cable-and-turnbuckle brace for the same reason. Infill comes last; it’s the lightest part of the decision.
- Hinges, latch, drop rod, stops. Adjustable barrel hinges rated for the leaf weight, plumbed so the gate neither self-opens nor self-closes on a slope. Double gates get a drop rod into a sleeve in the driveway and a positive stop, because solid-infill gates on north-county and east-bench lots see canyon gusts that treat a closed leaf like a sail.
- Finish for the elevation. Powder coat on steel, stain on cedar. UV at 4,500 feet chalks finishes faster than at sea level, and the coating spec reflects that.

Between stone or brick pilasters, the steel hinge post goes in first and the masonry is built around it; a hinge bolted to a pilaster face is a crack waiting to happen. On commercial drives we confirm fire-access clear width with the city before the design is final.
What does a driveway gate cost in Utah?
As ballpark planning numbers, not quotes: a manual driveway gate along the Wasatch Front runs from the low thousands for a single-swing cedar or vinyl gate on new steel posts, to the mid-to-high thousands for a welded steel double-swing with ornamental infill, and into five figures for wide cantilever slide gates, custom designs, and gates between new masonry pilasters. An operator prices separately.
What moves the number: opening width (which drives leaf weight, hinge rating, and post size), swing versus slide, infill, pilasters, cutting the driveway for a drop-rod sleeve or slide track, and conduit for a future operator. In HOA communities across Lehi, Saratoga Springs, and Eagle Mountain, a design submittal adds a couple of weeks. You’ll get a budget range after a site walk and a firm estimate once gate type and infill are settled. One B100 license, verifiable at dopl.utah.gov, covers the gate, the steel fence or fence repair that often comes with it, and the rest of our site, structure & envelope work.

Questions we actually get
How wide should a driveway gate be?
Twelve feet clear is the practical minimum for a single-car drive; 14 to 16 feet is comfortable for trucks and trailers, and double-wide drives usually want 18 to 20. Measure the vehicle you’re worst at parking, add room for the turn off the street, and ask your city about fire-access minimums.
Why do driveway gates sag, and how do you prevent it?
Two causes: the hinge post moves in the ground, or the frame racks under its own weight. Oversized posts below frost depth handle the first; a welded frame with a diagonal brace from bottom hinge corner to top latch corner handles the second. Adjustable hinges take up what little seasonal movement remains.
My driveway slopes up from the street. Can I still have a swing gate?
Sometimes. An out-swing gate set back from the sidewalk, or a leaf hung with extra ground clearance, works on a mild grade. On a steeper drive the swing arc hits pavement and a slide or cantilever gate is the honest recommendation. We shoot the grade at the site walk.
Can a manual driveway gate be automated later?
Yes, if it was built for it: hinge posts sized for an operator’s load, a frame stiff enough not to twist under the arm, and conduit stubbed to the post before the footing is poured. We build to that standard by default, so adding an operator later is hardware and wiring, not a rebuild.
Tell us what you’re working on
Send the opening width and a photo of the driveway from the street. We reply within a couple of hours during business hours — a day at most — with a straight read on gate type, scope, and budget.