Automatic Gates & Gate Operators in Utah
An automatic gate pairs a driveway or security gate with a motorized operator, entrapment-protection sensors, and the keypad, remote, or vehicle loop that opens it. Grandview builds the gate, sets the posts, installs and commissions the operator, and coordinates the licensed electrician for its circuit under one B100 license in Utah County and Salt Lake County.

When an automatic gate is the right choice
Automation earns its cost when the gate cycles several times a day or nobody should have to get out of the car to open it: gated homes on larger lots, multifamily communities with controlled entries, and commercial yards where the gate is part of the security plan. If you open it twice a year, a well-hung manual driveway gate is the better spend; if people walk through rather than drive, a pedestrian gate with a self-closing hinge and keypad lock costs far less.
The operator also changes how the gate must be built. A manual gate that drags at the latch is an annoyance; an automated gate that drags burns out a motor and stops opening on the coldest morning of the year. So we treat gate, operator, and power as one system, whether the leaf is a custom-fabricated steel gate, ornamental iron on a wrought iron fence, or a heavy slide panel on a steel security fence. It’s the same license that covers the rest of our fence installation and repair and site, structure & envelope work, verifiable at dopl.utah.gov.
Swing operator or slide operator?
Swing operators suit level driveways with room for the leaf to arc inward; slide operators suit sloped approaches, tight setbacks, and wide openings. On bench lots, slope decides more often than taste: a driveway that climbs toward the house makes an inward-swinging leaf hit the pavement, and a cantilever slide gate running along the fence line solves it cleanly.
Within each type, the choices matter. For swing gates, a linear-arm operator is the usual residential pick; an articulating arm handles wide pilasters and leaves that must swing past 90 degrees. For slide gates we lean toward cantilever over track-guided designs, because a ground track fills with snow, gravel, and plow berm every winter, and a cantilever gate rides on rollers above all of it. Solar operators are a real option for a ranch entry far from the panel, with battery capacity sized for short December days.
Wind is the other Utah variable. A solid privacy-style gate on an east-bench or north-county lot is a sail, and a canyon-wind event will stall an undersized operator or bend an underbuilt frame, so on exposed sites we open up the gate design or step the operator up a class and stiffen the frame.

What an automatic gate installation involves
- Site layout and power plan. We measure the opening, its slope, the run-off room or swing arc, and the distance back to power, and call utility locates before any trenching.
- Gate structure. The leaf is framed to carry its weight without sag and to meet the gate-construction standard operators are listed against: no reach-through openings near pinch points, screening on slide gates, positive stops so a slide leaf can’t leave its rollers.
- Posts and footings. Hinge posts, catch posts, and the operator pad go below frost depth — generally 30 inches or more here — with footings sized for the gate’s mass and for expansive clay that shifts anything shallow. A heaved operator pad throws the whole gate out of alignment.
- Power and conduit. Most operators need a dedicated 120-volt circuit in buried conduit from the panel to the pad, plus low-voltage conduit for keypads, loops, and photo eyes. Grandview holds the contract and coordinates a licensed electrician for the circuit and connection; we trench, sleeve, and sequence so it happens once.
- Operator and safety devices. The operator is mounted, the leaf balanced, and the entrapment protection installed and tested: monitored photo eyes across the opening and contact edges on the leaf, as the UL 325 operator standard calls for. A gate with no edge sensor is not finished.
- Access control and commissioning. Keypad, remotes, phone or cellular intercom, a free-exit loop in the driveway, and an emergency vehicle access device where your city’s fire marshal requires one. We set timing, force limits, and auto-close, then walk you through the manual release.

What does an automatic gate cost in Utah?
As ballpark planning numbers, not quotes: a residential swing operator with photo eyes, edge sensors, a keypad, and remotes typically runs roughly $3,500–$8,000 installed along the Wasatch Front. Slide operators with a cantilever gate usually land around $6,000–$14,000, and commercial-duty systems with vehicle loops, intercoms, and fire department access run higher. The gate itself prices separately.
What moves the number: swing versus slide, gate weight and width, trench length from panel to gate, whether the electrician finds spare panel capacity or needs a subpanel, solar versus hardwired, the access devices you choose, and rock or heavy clay in the footing holes. A short conduit run to a level driveway is the inexpensive version; a 300-foot trench to a sloped ranch entry with a cellular intercom is not. Budget range after a site walk; firm estimate once the operator and devices are specified.
Questions we actually get
Can you automate the gate I already have?
Often, if it passes a few checks. The leaf has to swing or slide freely with no drag, the hinge and catch posts have to be plumb and stable, and there can’t be reach-through gaps near pinch points. Many older Utah gates need new posts or a stiffened frame first, and we’ll tell you which at the site walk.
Does an automatic gate need a permit or inspection?
The electrical circuit does; the licensed electrician we coordinate pulls that permit and schedules the inspection. The gate itself may or may not, depending on height and city. Gated driveways in many cities also need a fire department access device, so we confirm with your city’s building department and fire marshal before ordering hardware.
How does the gate handle a Utah winter?
Design for it up front. Cantilever slide gates avoid the ground track that snow and plow berms pack full, and swing gates need their arc kept clear, which setting the gate back from the street helps. Low-temperature-rated operators, battery backup, and a manual release cover the rest.
What happens when the power goes out?
Every operator we install has a manual release so the gate opens by hand, and we show you how before we leave. Battery backup, optional on most residential units and standard on many commercial ones, keeps the gate cycling through a short outage and can be set to fail open or closed.
Tell us what you’re working on
Send the opening width, a photo of the driveway from the street, and where your panel sits. We reply within a couple of hours during business hours — a day at most — with a straight read on swing versus slide, power, and budget.