Site, structure & envelope

Mineral-based composite deck installation in Utah County

Mineral-based composite decking is a polypropylene board filled with mineral instead of wood flour, so it absorbs no water and barely moves with temperature. Grandview installs it on new and rebuilt decks across Utah County under a B100 general contractor license.

Discuss a project   Or call (385) 236-1741

Deck chairs and table on a composite deck overlooking a lake and mountain landscape

When a mineral-based board beats standard composite or PVC

Capped wood-plastic composite is a wood-flour-and-plastic core wrapped in a shell. Cellular PVC drops the wood but expands and contracts more than either. Mineral-based composite replaces the wood flour with mineral filler in a polypropylene matrix, and that filler drives its behavior. It’s the right pick when your deck faces one of these conditions:

  • Long board runs in full sun. A 20-foot board on a west-facing walkout in Saratoga Springs sees a 60-degree swing between a July afternoon and the next dawn. Mineral-based boards publish some of the lowest expansion figures in the category, so end gaps and picture-frame miters stay tight.
  • Water on the surface, not just rain. Hot-tub surrounds, pool-side decks, boards that meet grade. With no wood content there is nothing to swell or feed mold, and several lines are warranted for ground and water contact.
  • Second-story and bench-lot decks. The boards run roughly a third lighter than traditional composite, which you notice when every one goes up a ladder on an elevated deck.

It’s a poorer fit if you want the lowest-cost synthetic surface, and for a deck that must be noncombustible, aluminum decking is the better conversation.

What installing mineral-based composite involves

The frame is the same pressure-treated structure described on our deck construction page. What changes is everything from the joist tops up.

  1. Joist spacing is set by the board. Most mineral-based profiles are rated for 16-inch spacing on residential decks, 12 inches for diagonal layouts and stair treads. We frame to the installation guide for the exact board you choose, because the warranty is written to it.
  2. Joist tape still matters. The board won’t rot, but the joist under it can, so we tape joist tops and ventilate the underside exactly as we would under wood.
  3. Hidden fasteners in a grooved edge. Boards are grooved for clip systems; color-matched plugged screws finish perimeter boards and stairs.
  4. Gapping follows the manufacturer’s chart. Side gaps stay open for drainage; end gaps are smaller than PVC needs and are set from the air temperature at install.
  5. Cuts and edges. The board cuts with carbide blades and leaves a fine mineral dust that crews mask and collect. Most lines are solid color through the board rather than a cap over a core, so cut ends and scratches don’t expose a different-colored interior.

We photograph the frame and fastener layout before the last boards go down and hand the photos over with the warranty registration. If the deck includes lighting, Grandview holds the contract and manages licensed electricians so wiring runs before the surface closes.

Power drill, metal bracket, and gloves laid out for fastening deck boards to a joist

How a mineral-based board handles the Wasatch Front

Freeze-thaw is where this board wins outright. Across 100-plus freeze-thaw days a year, wood-flour composite can take on moisture at cut ends and screw holes, and it freezes. A mineral-filled board has nothing to absorb it, so there’s no end-swell after a hard winter, and a shovel slides across it without catching a cap edge on a north-facing Alpine deck that holds snow for months.

Heat is a mixed result. Mineral content tends to run cooler than solid PVC of the same color, but a charcoal board on a south-facing deck in Lehi will still be too hot for bare feet in August, so we steer sun-exposed decks toward lighter colors. UV fade at our elevation is handled by pigment stabilizers rather than a cap, with fade warranties competitive with capped composite. Those warranties depend on the installation following the guide, which is why we don’t improvise on spacing or fasteners. Our license is verifiable at Utah DOPL.

What does a mineral-based composite deck cost in Utah County?

As ballpark planning numbers, not quotes, a mineral-based composite deck in our market typically runs about $70–$100 per square foot installed with footings, framing, and standard railing, which puts it in the upper composite range and alongside cellular PVC. A 300-square-foot deck lands around $21,000–$30,000.

  • Board line and color. Within a single manufacturer such as Deckorators, the mineral-based lines span a real price range; multi-tone and wide-plank boards sit at the top.
  • Fastening and layout. Hidden clips, picture framing, and 12-inch spacing for a diagonal pattern all add framing and cutting time.
  • Height and railing. Elevated decks and custom stairs and railings move the number more than the decking itself.

After a site walk you’ll get a budget range, then a firm estimate once selections are made.

Finished low-maintenance deck with outdoor dining set beside a landscaped yard

Questions we actually get

Is mineral-based composite the same as regular composite decking?

No. Standard composite is wood flour and plastic, usually with a protective cap. Mineral-based composite replaces the wood flour with mineral filler in a polypropylene base: a lighter board with no organic content, far less thermal movement, and no cap, which is why it behaves differently in sun, snow, and water.

Can mineral-based boards go on my existing deck frame?

Only if the frame passes inspection and the joist spacing matches the board’s rating. Many older decks are framed at 24 inches; most mineral-based profiles require 16. We can sister joists to close the spacing, but if the ledger, posts, or footings are failing, resurfacing isn’t the right move and we’ll say so.

Does mineral-based decking get hot in Utah sun?

Less than solid PVC of the same color, but any dark board in direct summer sun will be hot. Color matters more than material. We recommend lighter boards on south- and west-facing decks, and we’ll leave samples in your yard so you can check surface temperature in the afternoon before deciding.

Why does it cost more than standard composite?

The board is priced at the premium end, and most lines install with hidden clip systems that add labor. In exchange you get lower expansion, lighter handling, water-contact ratings on some lines, and solid-color construction that hides scratches. On a deck in heavy sun or standing water, the premium usually earns its keep.

Tell us about the deck you have in mind

We reply within a couple of hours during business hours, a day at most. You’ll get a straight read on board options, framing, and budget before anyone commits to anything, as with all our site, structure & envelope work.

Request an estimate   (385) 236-1741