Renovation & Build-Outs · Tile & Stonework

Schluter & Kerdi shower waterproofing systems in Utah

A Schluter Kerdi shower is a bonded sheet-membrane assembly that stops water at the tile surface instead of catching it behind the wall. Grandview Contractors installs Kerdi trays, drains, membranes, and seals to the manufacturer’s spec, flood-tests the pan, then tiles it, across Utah County and Salt Lake County under a Utah DOPL B100 general contractor license.

Discuss a project   Or call (385) 236-1741

Contemporary tiled bathroom with a bathtub and black and white tile, built over a bonded waterproofing membrane
When this system is the right call

When a bonded membrane beats a traditional pan

A conventional shower pan works by letting water through: it soaks past the tile into the mortar bed, reaches a PVC liner an inch or two down, and exits through weep holes. The bed stays damp for days, and the liner protects nothing above it. The backer and studs rely on grout and caulk that eventually open up.

A Kerdi assembly moves the waterproofing to the top of the stack. The membrane bonds directly under the tile, so the backer, tray, and framing stay dry by design. It’s the right fit for a shower that has already leaked once, a shower over finished space, a curbless or linear-drain layout, or anyone who wants a written system warranty. If the membrane is only part of your question, see shower tile and surround installation. Steam changes the vapor spec; see steam shower and wet room tile. Tub walls that only see splash rarely need the tray-and-drain kit; that’s a tub surround.

One caveat: a Kerdi shower is only as good as its seams. The product doesn’t carry the install. The installer does.

The assembly

What a Kerdi shower actually contains

Schluter sells the shower as a kit of parts that only perform together:

  • Kerdi-Shower-Tray. A pre-sloped expanded-polystyrene pan bonded to the subfloor or slab. It replaces the hand-floated mortar bed, so the slope is right out of the box and never holds water.
  • Kerdi-Drain or Kerdi-Line. A drain with an integrated bonding flange the membrane adheres to directly. The linear version sits at a wall and allows a single-plane slope, which is what makes large-format floor tile and curbless entries possible.
  • Kerdi membrane or Kerdi-Board. Sheet membrane bonded over cement board or drywall, or Kerdi-Board, a foam panel that is already waterproof and only needs its joints sealed. Prefabricated Kerdi niches and curbs bond into the same layer.
  • Kerdi-Band, Kerdi-Kereck corners, and pipe seals. Band with a 2-inch overlap at every seam, preformed pieces at every corner, and a Kerdi-Seal gasket at the valve and shower arm. Corners and penetrations are where nearly every failed shower we open up went wrong.

The mortar matters as much as the membrane. Schluter specifies unmodified thinset, or its own SET and ALL-SET, for bonding Kerdi to Kerdi, because modified mortars cure by air exposure and can’t dry sandwiched between two sheets of polyethylene. The wrong bag voids the warranty and leaves seams that never fully bond. We use what the Schluter installation handbook calls for at each layer.

Finished shower and bathroom with contemporary fixtures and tile set over a Kerdi membrane assembly
How we install and test it

How a Schluter shower goes together on site

  1. Drain and substrate check. Drain location, trap, and slab or subfloor flatness. Moving a drain for a linear layout is plumbing work; Grandview holds the contract and manages the licensed plumbers who do it, then picks up at the flange. In Utah’s basement-heavy housing stock, that often means a drain set into a slab cut.
  2. Tray, curb, and drain bonded. Set in thinset and checked for full contact; a hollow under a foam tray is a crack waiting to form.
  3. Walls membraned, seams banded. Full-height sheets, preformed corners, band at the tray-to-wall joint. We photograph every seam before tile.
  4. Flood test, 24 hours. Drain plugged, pan filled above the curb line. Many Utah County and Salt Lake County cities want to see the pan test before it’s covered; verify the sequence with your city building department, and we schedule around it.
  5. Tile, grout, silicone. Tile bonds straight to the membrane, with silicone rather than grout at every change of plane. Wasatch Front homes over expansive clay move seasonally, and a bonded membrane with flexible corners tolerates that far better than a rigid mortar bed.

Problems happen. Surprises should not. A seam flaw found at the flood test costs an hour, not a demolition.

Budget honestly

What does Schluter shower waterproofing cost in Utah?

As ballpark planning numbers, not a quote: the Kerdi components for a standard alcove shower usually add roughly $600 to $1,500 in materials over a liner-and-mortar pan, more for Kerdi-Board walls or a linear drain. Inside a complete tiled shower rebuild in Utah, the whole shower typically lands between $5,000 and $13,000 depending on size, tile, and what demo reveals. The membrane is a small share of that total and the share you should be least willing to trim.

What moves the number most: linear versus point drain, a recessed subfloor for a curbless entry, Kerdi-Board versus membrane over backer, niches and benches, and whether the drain has to move. A curbless shower conversion carries most of those at once. A Kerdi shower is one assembly inside our tile and stone installation work and most renovation projects; if you’re chasing an active leak rather than planning a rebuild, start with bathroom and shower waterproofing diagnosis. Grandview’s B100 license is verifiable at dopl.utah.gov.

Renovated bathroom with a ceramic tub and tiled walls after a full wet-area rebuild

Questions we actually get

Is Kerdi better than RedGard or another liquid membrane?

Both can meet the bonded-waterproofing standard, ANSI A118.10. Liquid membranes depend on the installer hitting a minimum dry-film thickness in two or more coats, which is hard to verify afterward. Kerdi is a fixed thickness off the roll, with seams you can see and test. We default to Kerdi for showers.

Can you install Kerdi over my existing cement board or drywall?

Over sound, dry, flat cement board, yes. Schluter also permits Kerdi over standard drywall, though we replace stained or soft board rather than membrane over it. An old mortar-bed pan means a full rebuild, because a new tray can’t bond to it.

Does a Schluter shower come with a warranty?

Schluter offers a system warranty when the shower is built entirely from Schluter components and set with the mortar they specify. A different drain or the wrong thinset can void it. We build to that spec, document it with photos, and point you to the current terms on Schluter’s site before you decide.

How long before I can use the shower?

Roughly one to two weeks from demo to first use: a day or two for tray, membrane, and seams, 24 hours for the flood test, then tile, grout cure, and silicone cure. Rushing the last two days undoes the rest. A full bathroom remodel around the shower adds its own schedule.

Tell us what you’re working on

We reply within a couple of hours during business hours, a day at most. You’ll get a straight read on scope, sequence, and budget before anyone commits to anything.

Request an estimate   (385) 236-1741