Renovation & Build-Outs · Tile & Stonework

Shower tile & surrounds in Utah County

A tiled shower is a sloped, waterproofed box that happens to have tile on it: pan, curb, walls, and niche built over a membrane that is flood-tested before any tile goes on. Grandview Contractors builds and tiles showers across Utah County and Salt Lake County under a Utah DOPL B100 license.

Discuss a project   Or call (385) 236-1741

Glass-enclosed tiled shower with gray subway tile walls in a compact bathroom
Right page, right scope

When a tiled shower is the right call, and when a neighbor page fits better

This page covers stand-alone showers: a tiled pan, walls that take direct spray, and a glass door or curtain to finish. It’s the right scope when a fiberglass unit has cracked or yellowed, when a tub is coming out for a walk-in shower, or when a pan is leaking into the ceiling below.

If the tile wraps a bathtub, the tub is the pan and the waterproofing stops at its lip, so that job belongs under tub surround tile. A steam generator or a curbless wet room needs a vapor-tight assembly under steam shower and wet room tile. The membrane install itself is detailed under Schluter and Kerdi shower waterproofing, and the floor outside the glass under bathroom floor tile. All of it sits inside Grandview’s tile and stone work and renovation services, often as one line of a larger bathroom remodel.

What the work involves

What goes into a shower that stays dry behind the tile

Tile and grout are not waterproof. Water passes through grout joints every time the shower runs; the assembly behind the tile carries it to the drain. Showers fail when that assembly is flat, has an unsealed seam, or has grout where silicone belonged.

  1. Demo and framing check. We strip the old unit to the studs, check for rot at the bottom plate and valve, and plumb the walls, because out-of-plane framing shows up as crooked grout lines at eye level. The niche is framed now, between studs, at a height that clears the glass line.
  2. Plumbing rough-in. Relocating the drain, swapping to a bonded-flange drain, or setting a new valve is licensed plumbing work. Grandview holds the contract and manages the licensed plumbers who do it; we coordinate, sequence, and quality-check it inside your project. Moving a drain usually needs a plumbing permit; verify with your city building department.
  3. Pan and pre-slope. A mortar bed pitched 1/4 inch per foot to the drain in every direction. With a clamping drain that slope goes under the PVC liner (the pre-slope) so water reaching the liner still drains; with a bonded membrane, the sloped bed is the only bed and the membrane goes on top. The curb is pitched inward and wrapped in the same membrane. This is the step most leaking showers skipped.
  4. Walls and waterproofing. Cement backer or foam board, then a bonded sheet membrane like Schluter’s Kerdi or a liquid membrane rolled to spec thickness. Inside corners, curb, niche, and the valve and showerhead penetrations get preformed corners and collars, because seams are where showers leak. Then the pan is plugged and filled for a 24-hour flood test. If the level drops, we fix it before a single tile goes on.
  5. Tile set. Layout is decided first so full tiles land at the sight lines: curb top, niche sides, the wall you see from the door. Pan tile is small enough to follow the slope, typically 2-inch mosaics or smaller. Niche shelves and the curb top get a slight pitch back into the shower.
  6. Grout, silicone, and glass. Grout in the field; silicone, not grout, at every change of plane: corners, wall-to-pan, wall-to-curb, around the niche. Cement grout gets sealed once cured. Glass is measured after tile and installed about a week later.
Tiled shower wall with mosaic accent band and a recessed niche

Two Utah details shape these choices. Wasatch Front water is hard, so glass spots quickly and unsealed cement grout takes on mineral stains; a squeegee and sealed grout do more for a shower over ten years than the tile pattern does. And in basement bathrooms the pan sits on a slab that moves with Utah County’s expansive clay soils, which a bonded membrane tolerates better than a rigid liner pan.

Budget honestly

What does a tiled shower cost in Utah?

As ballpark planning numbers, not a quote, a tiled shower rebuild in Utah County typically runs $5,000 to $14,000 including demo, waterproofing, tile, and grout, plus roughly $1,200 to $3,500 for glass. A tub-to-shower conversion lands at the upper end because the drain moves and the pan is built from scratch. What moves the number:

  • Drain and valve location. Leaving both where they are keeps plumbing and permit scope small. Moving a drain across a slab means cutting concrete.
  • Niches and benches. Each adds framing, membrane corners, and trimmed tile edges; a bench is a sloped, waterproofed box of its own.
  • Tile format. Large-format wall tile sets faster but demands flatter walls; mosaics set slowly; natural stone needs sealing.
  • What the demo finds. Rot at the bottom plate or a soft subfloor under the old pan gets repaired first, and it’s the most common change order.

Grandview’s B100 license is verifiable at dopl.utah.gov. Shower assemblies follow the Tile Council of North America handbook and the membrane manufacturer’s spec, whichever is stricter.

Finished bathroom with a tiled walk-in shower and contemporary fixtures

Questions we actually get

Can you keep my existing shower pan and just retile the walls?

Rarely. A new wall membrane has to lap over the pan’s waterproofing, and a fiberglass pan or an old flat mortar bed gives us nothing to lap onto. Unless the pan is sound, sloped, and tied into a system we can verify, it comes out with the walls.

How long will the shower be out of service?

Plan on about two weeks. Demo and plumbing take two or three days, pan and waterproofing two more including the flood test, tile and grout three or four, then cure time. Glass arrives about a week after measuring, and the first shower waits for silicone to cure.

Should the shower walls be tiled to the ceiling?

If the enclosure has a door, yes, or at least to the top of the glass; tile keeps steam and spray off drywall, which stains and softens otherwise. For an open-top curtain shower, tile to about 7 feet and finish above with moisture-resistant paint.

Why is a tiled shower more expensive than a drop-in unit?

A one-piece unit is one part set in a morning. A tiled shower is a built assembly: framing, plumbing, sloped pan, membrane, flood test, tile, grout, glass, each with cure time between. You are paying for the waterproofing sequence, not the tile. In return it fits any footprint and can be repaired in sections.

Tell us what you’re working on

We reply within a couple of hours during business hours — a day at most. You’ll get a straight read on scope, sequence, and budget before anyone commits to anything.

Request an estimate   (385) 236-1741