Portable Generator Hookups
A portable generator hookup is a weatherproof power inlet on the outside of your house, wired through an interlock kit or manual transfer switch, so a generator you already own can feed your furnace, refrigerator, and lights through one cord. Grandview Contractors coordinates the installation across Utah County and Salt Lake County under our B100 general contractor license, with a licensed electrician doing the wiring.

Portable hookup, standby unit, or battery: which backup fits
A portable generator hookup is the right choice when you’ll be home during an outage, you own a 5,000- to 12,000-watt portable unit, and the goal is to keep essentials running: furnace blower, fridge and freezer, sump pump, a bedroom circuit. It’s the lowest-cost route to safe backup.
If the loads must be covered while nobody’s home, a standby generator that starts itself is the honest recommendation. For silent backup through short outages, home battery backup competes on convenience but runs out in hours, not days. This scope is narrower than our generator transfer switch page, which also covers automatic switches for permanent units. If your panel is full or undersized, an electrical panel upgrade may need to come first; we’ll say so plainly.
How a portable generator hookup gets specified and installed
Grandview holds the contract and manages a licensed electrician for the wiring; we pull the permit and quality-check the installation before the inspector sees it. Both licenses are verifiable at dopl.utah.gov. Most hookups are a single visit.
- Match the inlet to the generator outlet. Most 5,000- to 8,000-watt portables carry a four-prong NEMA L14-30 twist-lock outlet, which pairs with a 30-amp inlet box, 30-amp breaker, and 10-gauge cord. Larger 10,000- to 12,000-watt units add a 14-50 outlet, which calls for a 50-amp inlet and 6-gauge wire. We size to the generator you actually have.
- Interlock kit or manual transfer switch. An interlock is a listed mechanical slide on your panel cover that makes it impossible for the main breaker and the generator breaker to be on together; you back-feed the whole panel and choose circuits by flipping breakers. A manual transfer switch is a separate six- to twelve-circuit sub-panel that moves pre-selected circuits only. Interlocks are cheaper and more flexible; a manual switch is the answer when no listed interlock exists for your panel.
- Place the inlet where the generator can live safely. The inlet mounts near the panel to keep the conduit run short, but positioned so the generator can sit away from doors, windows, and the furnace intake. The Consumer Product Safety Commission says at least 20 feet from the home with exhaust pointed away; carbon monoxide is how these units hurt people, and inlet location decides whether 20 feet is realistic.
- Sort out the neutral bond. Most portables ship with the neutral bonded to the frame. Feeding a house panel that already has its own neutral-ground bond creates a parallel path that trips the generator’s GFCI outlets. The electrician advises a floating-neutral conversion or a bonding plug. This is the most common reason a new hookup “doesn’t work” on the first storm night.
- Label, test, and walk through. The generator breaker gets a permanent label; we start the unit, throw the interlock, and confirm the furnace and sump come up. You get a written start-up sequence to tape inside the panel door.


Why your generator makes less power in Utah than the box says
Portable generators are rated at sea level. Gasoline engines lose roughly three to four percent of output per 1,000 feet, so a unit on a Provo lot at 4,500 feet is down about 15 percent before it starts, and a bench lot in Alpine or Draper gives up more. Cold compounds it: a January outage after a canyon-wind event means a cold-soaked engine and a furnace blower with a starting surge two to three times its running draw. We size against the derated number, not the nameplate.
Fuel matters too. A gasoline portable at half load empties a five-gallon can in roughly eight to twelve hours, and stored gasoline degrades over a season. Dual-fuel units running on propane solve both; if that means a new gas connection, a gas line extension folds into the same project.
What does a portable generator hookup cost in Utah?
As a ballpark planning range, an interlock kit with a 30-amp inlet box, cord, and permit typically installs for $700 to $1,500 along the Wasatch Front, and a manual transfer switch setup for $900 to $2,000. These are planning numbers, not quotes. What moves the price: a 50-amp inlet and 6-gauge run instead of 30-amp; a long conduit path when the panel sits opposite the only safe generator spot; a panel with no listed interlock. The generator itself is separate. A call gets you a budget range; a site visit gets you an estimate; the proposal is the fixed number.
Questions we actually get
Can I run my whole house from a portable generator through the interlock?
You can back-feed the whole panel, but not run everything at once. A 7,500-watt unit at Utah elevation delivers around 6,000 usable watts: enough for furnace, fridge, freezer, sump, and lights, not for central air, an electric range, or a dryer. You choose by flipping breakers, which is the interlock’s main advantage over a fixed-circuit manual switch.
Why does my generator’s GFCI trip the moment I plug into the inlet?
Almost always a bonded neutral. The generator’s frame-to-neutral bond and the house panel’s bond create two ground paths, and the GFCI reads the difference as a fault. The fix is a floating-neutral conversion or a listed bonding plug, depending on the model. It’s a check we build into every hookup install.
Does a portable generator hookup need a permit in Utah?
Yes. The inlet, breaker, and interlock or switch are a permanent change to your electrical service, and the cities we work in treat it as permitted electrical work with an inspection. We pull the permit and schedule the inspection; verify specifics with your city building department.
Will the hookup work with a different generator later?
If the new unit has the same outlet type and a similar or smaller rating, the inlet and cord carry over. Moving from a 30-amp L14-30 to a 50-amp 14-50 unit means a new inlet, breaker, and wire. If an upgrade is likely, we’ll quote the 50-amp path up front.
Tell us what you’re working on
We reply within a couple of hours during business hours — a day at most. Tell us the generator model and where the panel sits, and you’ll get a straight read on inlet size, interlock versus switch, and budget. This scope lives inside our MEP & systems coordination work under renovation & build-outs.