Storm door installation in Utah
Storm door installation is the fitting of a second, lighter door — aluminum-framed, with interchangeable glass and screen panels — outside an existing entry door, mounted to the brickmould on a Z-bar frame with a closer and sweep. Grandview installs and replaces storm doors across Utah County and Salt Lake County under a B100 general contractor license, including the out-of-square openings on older homes where off-the-shelf fits go wrong.

When a storm door is the right choice, and when it isn’t
A storm door earns its place when the entry door behind it is sound but exposed: an east- or north-facing entry that takes winter wind head-on, or a porch-less door that catches horizontal rain in a summer cloudburst. It adds a still-air gap, a second seal, and a screen for the months you’d like the front door open.
It is the wrong answer in three situations. If the entry door itself is failing — rotted bottom rail, soft threshold, daylight at the latch — a storm door hides the problem, and entry door replacement is the honest fix. If the door is sound but faded, refinishing the existing door costs less. And if the draft is at the glass, storm windows are the matching answer for the rest of the wall. A storm door also doesn’t fit French doors or sliders. The whole family lives on the window and door installation page, inside site, structure & envelope.
One caution specific to Utah sun: full glass in front of a dark fiberglass or vinyl entry door on a south or west exposure traps enough July heat to warp the slab or bubble its finish. On those exposures we steer toward a ventilating door before anyone orders a full-view unit.
Full-view, ventilating, or screen door: choosing the style
Full-view doors are one large tempered-glass panel with a screen insert you swap each spring; they show off the entry door and seal tightest in winter. Ventilating doors carry a retractable screen that rolls into the top rail as the glass slides down — no seasonal panel to store — and they’re our default suggestion. Mid-view and high-view doors put a solid kick panel below the glass, which handles dogs, strollers, and snow shovels better than glass.
Frame gauge matters more than brand. Hollow aluminum is light and cheap but dents at the bottom rail; heavier aluminum with a foam or wood core resists denting and the chalking that budget finishes develop under high-elevation sun within a few seasons. Low-E storm glass is worth it on north-facing entries.
Hardware decides whether the door is a pleasure or a nuisance. A single pneumatic closer is standard; we specify dual closers and a wind chain on entries facing canyon-wind corridors like Centerville and Farmington, and on bench lots where gusts have torn a storm door off its hinges before.

How we install a storm door
- Measure the opening, not the old door. Storm doors mount to the exterior casing, so we need at least an inch of flat brickmould on both sides and the head. Width at three heights, height at both sides — a half-inch of difference is common on pre-1980 homes in Provo and Salt Lake City.
- Pick hinge side. Same side as the entry door so the handles clear each other, with the swing checked against any porch post before ordering.
- Prep the casing. Rotted brickmould gets replaced, not screwed through. On brick or stucco without wood casing, we anchor a treated or PVC buck first.
- Hang the Z-bar frame. The hinge-side rail is cut to the sill slope and set plumb with the door attached so we can read the reveal; then the latch rail and the drip cap, each shimmed to an even gap rather than to the crooked casing.
- Sweep, closer, and seal. The expander sweep is set to kiss the sill without dragging, closers tensioned so the door shuts without slamming, and gaps sealed with a sealant that stays flexible through 100-plus freeze–thaw days a year.
- Verify. Latch throw, screen operation, and a check that the entry door’s handle clears the storm door glass.

A storm door on a square opening with sound casing takes two to four hours; brickmould replacement or a masonry buck adds half a day.
What does storm door installation cost in Utah?
As ballpark planning numbers: a basic aluminum ventilating storm door runs a few hundred dollars for the unit, a heavy-gauge full-view door with retractable screen and low-E glass roughly a thousand or more, and labor on a sound, square opening typically adds a few hundred. Casing repair, a masonry buck, or a custom size push the total higher; we confirm a range after measuring.
Two things move price more than people expect. Anything outside the common 30-, 32-, 34-, and 36-inch widths roughly doubles the unit cost and adds weeks of lead time — routine on older Provo and Salt Lake homes with 7-foot openings. And hardware is a bigger share of the cost than on an entry door: dual closers and a keyed mortise lockset can add a third to the unit price.
A storm door is only worth buying if the entry behind it already seals reasonably well; the Department of Energy’s guidance on air sealing and weatherstripping is the right first read. Our license is verifiable at dopl.utah.gov, since a storm door is often the first small job a homeowner hires us for.
Questions we actually get
Can a storm door go on a brick or stucco entry with no wood casing?
Yes, with one extra step. The Z-bar frame needs a flat surface at least an inch wide on both sides and the head, so on masonry we first anchor a treated or PVC buck frame, then mount the storm door to it. It adds a couple of hours and a small material line.
Will a storm door damage my fiberglass or vinyl entry door?
It can, on south- and west-facing entries. Glass in front of a dark door traps heat on summer afternoons, and at Utah elevation that heat is enough to warp a slab or lift its finish. We check exposure and door color before ordering and recommend a ventilating door, screen deployed in summer, where the risk is real.
What moves the cost of a storm door installation up or down?
Unit style and frame gauge first, then hardware. A custom size roughly doubles the unit cost and adds lead time. On labor, rotted casing, a masonry buck, or an opening more than a half-inch out of square each add time. A sound, square, standard-width opening is the quickest job in this family.
Tell us what you’re working on
We reply within a couple of hours during business hours — a day at most. You’ll get a straight read on the door, the opening, and the budget before anything is ordered.