Site, structure & envelope

Impact & storm windows

Storm windows are a second layer of glazing fitted over the windows you already have; impact windows are replacement units with laminated glass and reinforced frames built to shrug off windborne debris. Grandview installs both across Utah County and Salt Lake County under a B100 general contractor license, and we’ll tell you plainly which one your house needs.

Discuss a project   Or call (385) 236-1741

Stone-and-wood bench-lot home with large windows exposed to open sky, the kind of exposure where storm windows earn their keep

When a storm or impact window beats replacing the window

Storm windows make sense when the primary window is sound but single-pane, drafty, or worth keeping. Older Provo and Salt Lake City homes with original wood sash are the classic case: a low-E storm panel brings a 1920s window close to double-pane performance for a fraction of the cost of new units, and the original glass stays put for a future window restoration.

Impact windows are a different decision. They replace the unit entirely with laminated glass, and the reason to choose them in Utah isn’t hurricane code, which doesn’t apply here. It’s exposure. Lots below the mouths of Provo, Spanish Fork, and Parleys canyons take wind that picks up gravel and branches, and a laminated lite holds together where a standard pane would shatter into the room.

If your frames are rotted or the seals have failed, neither is the right fix. That’s a replacement window job, and if lower bills are the whole goal, a low-E replacement unit may beat a storm panel over a tired primary. Storm doors follow the same logic for entries.

Exterior versus interior storm panels

Exterior storms are the triple-track aluminum units most people picture: two glass panels and a screen in a frame screwed to the casing. They shield the primary sash from weather and from UV that, at 4,500 feet, is harsher on wood and paint than at sea level. The detail that matters most is the weep holes along the bottom rail. They have to stay open so condensation and wind-driven rain can drain; a bead of caulk across the sill is the fastest way to rot it from behind. We seal the head and jambs, leave the sill to breathe, and set each frame to the blind stop so the panels track without binding.

Interior storms are compression-fit or magnetic panels mounted inside the room, the usual answer for historic districts and for HOA-governed neighborhoods in Lehi, Saratoga Springs, and Eagle Mountain, where anything visible from the street needs approval. The physics flips: the inner layer must be the tighter one, or warm room air reaches the cold primary glass and fogs it.

Either way, we spec low-E glass where the budget allows; the U.S. Department of Energy rates low-E storm windows a cost-effective upgrade over single-pane and older double-pane glass.

Row of older homes with original wood windows and painted facades, candidates for interior or exterior storm panels

What makes an impact window different

An impact unit uses laminated glass: two lites bonded to a polyvinyl butyral or ionoplast interlayer, the same construction as a windshield. The glass may crack on impact, but the interlayer keeps the pane in one piece and in the frame. The frame is heavier, with a deeper glazing pocket and more fasteners per foot. Units tested to the ASTM E1886 and E1996 windborne-debris standards carry a design-pressure rating, and we match that rating to your lot’s exposure rather than buying the heaviest unit sold.

Installation differs too. The shims have to carry a heavier unit without crushing, so we block the rough opening instead of relying on foam, and the sill pan and back dam are non-negotiable: a window built to resist 100 mph gusts still fails if water gets behind the flange. On exposed bench lots, where canyon-wind events test fastening more than snow load ever will, that anchoring is the point. A side benefit along the Wasatch fault: laminated glass that cracks in a quake stays in the opening.

How a storm or impact window project runs

  1. Assess the primary. For storm panels, we confirm the existing window is sound, square, and tight enough to pair with the panel. Rot changes the recommendation before anything is ordered.
  2. Measure each opening. Storm panels are made to the casing, impact units to the rough opening, and older homes are rarely square.
  3. Handle approvals. Street-facing exterior storms often need HOA sign-off; interior panels usually don’t. Impact replacements are permitted like any window replacement.
  4. Install and seal. Storm frames set to the blind stop, sealed on three sides, weeps open. Impact units flashed, blocked, and fastened to the manufacturer’s tested schedule.
  5. Operate and verify. Every track slides, every panel latches, every weep drains.
Fasteners, drill bits, and sealing tools laid out for a storm window installation

What storm and impact windows cost in Utah

These are ballpark planning numbers, not quotes. Exterior triple-track aluminum storm windows typically land around $150 to $450 per opening installed, with low-E glass adding roughly $50 to $100 each; interior panels run a similar range. Impact-rated replacement windows are a different tier, commonly $600 to $1,500 or more per unit installed, driven by design-pressure rating, frame material, and any flashing repair the opening needs. Second-story access and out-of-square historic openings push labor up; opening count pulls the per-unit price down.

Questions we actually get

Do storm windows actually help in Utah’s climate?

Yes, especially over single-pane glass. The trapped air layer cuts heat loss through 100-plus freeze–thaw days a year, and a low-E coating turns back summer heat and the UV that fades floors at our elevation. They won’t rescue a window that’s already rotted or leaking.

Can I put storm windows on a historic home without changing its look?

Interior panels are invisible from the street and leave the exterior untouched, which is why historic-district reviewers generally prefer them. If you want exterior storms, low-profile units with a color-matched frame and narrow meeting rail keep the original sightlines.

Are impact windows required by code anywhere in Utah?

No. Windborne-debris requirements apply to hurricane-prone coastal regions, and current Utah-adopted code does not mandate impact glazing for homes. People choose them here for canyon-wind exposure, security, or sound. Commercial occupancies can carry their own glazing rules, so confirm with your city’s building department.

Why is one of my storm windows fogging up?

Moisture is getting between the storm and the primary and can’t get out. On exterior storms, the weep holes are blocked or were caulked shut. On interior storms, the primary window is leaking warm air into the gap. Both are fixable.

Tell us what you’re working on

We’ll give you a straight read on which option fits your openings. See the rest of our window and door work and the wider site, structure and envelope family. We reply within a couple of hours during business hours, a day at most.

Request an estimate   (385) 236-1741