Site, structure & envelope · Doors

Garage door & opener installation in Utah County

Sectional garage doors and opener systems installed on homes, shops, and small commercial buildings — opening checked, springs balanced to the door’s real weight, safety reversal tested before we leave. Grandview installs them under a Utah B100 general contractor license across Utah County and Salt Lake County.

Discuss a project   Or call (385) 236-1741

Row of suburban homes with newly installed sectional garage doors under a clear sky

When a garage door install is the right scope

This page covers the overhead door and the motor that moves it. It’s the right scope when a door’s panels or springs are done, when a new or converted garage needs its first door, or when you want an insulated, wind-rated, or full-view glass door in place of a builder-grade steel one. Opener-only replacement counts too.

Two neighbors in our window and door family, part of site, structure & envelope, are easy to confuse with this one. The swinging door from garage to house is a fire-rated door with its own code rules. The man door into a detached shop is an entry door. If you’re building the garage itself, start at detached garage construction; if the slab at the threshold has heaved, the fix is a garage floor slab repair first and a door second.

What the work actually involves

A garage door is the largest moving object in most buildings, and most failures we’re called to fix trace back to the opening, not the door. So that’s where we start: width, height, and square; jambs plumb with solid backing; and headroom, which decides the track style. A standard torsion setup wants roughly 12 inches of clear headroom; below that, a low-headroom kit changes the hardware. In a tall shop, a high-lift track lets the door rise nearly to the ceiling, which matters if you plan a vehicle lift.

Then the door itself: single-layer steel, steel-polystyrene-steel sandwich, polyurethane-injected panels in the R-12 to R-18 range, wood, or full-view aluminum and glass. On an attached garage in Lehi or Sandy, where a bedroom often sits above the door, an insulated door pays back in comfort. On a detached shop, the choice is about noise and dent resistance as much as temperature.

Springs get sized to the measured door weight, not the catalog weight — a glass door and a steel door of the same size can differ by a hundred pounds. Tracks are set to the manufacturer’s gap, and the opener is mounted to blocking, not drywall. Openers are chain, belt, or wall-mounted jackshaft; we recommend jackshaft units for high-lift doors and for finished ceilings you’d rather not hang a rail through.

Empty steel-walled shop interior with workbenches, the kind of space that takes a high-lift garage door and jackshaft opener
Power drill, mounting bracket, and safety gloves staged for a garage door opener installation

How we run a garage door project

  1. Measure the opening, not the old door. Width, height, headroom, side room, backing, and the slab condition at the threshold — a heaved edge is the most common reason a new door still lets in snow.
  2. Specify door, track, and opener together. Panel construction, R-value, windows, wind-load rating, and the opener type the headroom allows. In an HOA-governed development, we fold the appearance submittal into the schedule.
  3. Order and confirm. Stock steel doors ship in days; custom wood, glass, and odd sizes run several weeks. The old door stays up until the new one is on site and checked.
  4. Install and balance. Old door and springs removed safely, new tracks hung, springs wound to balance, opener travel and force limits set.
  5. Safety test and walkthrough. Photo-eye alignment, the 2-by-4 reversal test, manual release, and remotes programmed in front of you.

What does garage door installation cost in Utah?

As ballpark planning numbers: a single-car non-insulated steel door installed usually lands between $1,200 and $2,500; an insulated two-car door between $2,500 and $5,500; custom wood or full-view glass doors from about $6,000 up. A chain or belt opener adds roughly $450 to $900 installed; a jackshaft unit $800 to $1,400. These are not quotes — we give a budget range after measuring and a firm estimate before ordering.

What moves the number: panel construction and insulation, window lites, wind-load reinforcement, opener type, and whether the opening needs framing or slab work first. Exposure matters here. East-facing doors on bench lots and anywhere in the Centerville–Farmington canyon-wind corridor should get reinforcement struts or a rated door; DASMA, the garage door industry’s standards body, publishes the wind-load guidance manufacturers rate against. At 4,500 feet and up, UV is also harder on painted steel and stained wood, so finish warranty terms belong in the comparison.

One more Utah line item: the bottom seal. With 100-plus freeze–thaw days a year, the slab edge under the door moves, and a door set to a summer floor can show daylight by February. We fit the seal to the real floor and, where the gap is uneven, add a surface-mounted threshold rather than cranking the door down into the concrete.

Questions we actually get

Can I replace just the opener and keep my garage door?

Yes, if the door is balanced and the springs are healthy. We test that first: a balanced door stays put when lifted halfway by hand. If it slams or drifts, the springs need attention before any opener goes on — a motor fighting an unbalanced door burns out early.

Do I need a permit for a garage door in Utah County?

A like-for-like door swap usually doesn’t need one, but a new or enlarged opening does, because the header above it is structural. Electrical for a new opener outlet is permitted work as well, which we coordinate through a licensed electrician. Verify with your city’s building department, since Provo, Orem, and Lehi handle it slightly differently.

Is an insulated garage door worth it on an attached garage?

Usually, yes. An attached garage shares at least one wall and often a ceiling with living space, and an R-12 to R-18 door keeps that buffer zone far closer to room temperature through a Utah winter. It’s also quieter and stiffer, which means fewer dents. On a detached shop you don’t heat, the case is weaker.

What safety features should a new opener have?

Photo-eye sensors near the floor and automatic reversal on resistance have been required on openers for decades. Newer units add battery backup, rolling-code remotes, and app control. We test the reversal with a 2-by-4 on the floor at every install, and we’ll show you how to repeat it.

Tell us what you’re working on

A replacement door, an opener swap, or doors for a new shop — we’ll give you a straight read on scope, options, and budget before anyone commits to anything. We reply within a couple of hours during business hours, a day at most. Our B100 license is verifiable at dopl.utah.gov.

Request an estimate   (385) 236-1741