Site, structure & envelope · Masonry

Brick Repair, Tuckpointing & Repointing

Tuckpointing is the repair for brick whose mortar has failed before the brick has: deteriorated joints are cut out to a set depth and repacked with mortar matched to the original in color, profile, and strength, with spalled units replaced along the way. Grandview repoints brick across Salt Lake and Utah counties under a B100 general contractor license.

Discuss a project   Or call (385) 236-1741

Exposed brick wall mid-renovation with original mortar joints visible and ready for repointing

When repointing is the right fix, and when it isn’t

Run a key along a mortar joint. If it scratches out sand, crumbles, or has receded a quarter inch behind the brick face, the joint has stopped shedding water and started holding it. That is the repointing case: the brick is sound, the mortar is not, and new joints restore the wall for decades. Hairline cracks that follow the mortar, and a few spalled faces on a healthy elevation, belong here too.

It is the wrong fix for three things. Stair-step cracks running through brick and mortar alike are a foundation repair story; repointing over them hides the symptom for a season. Pre-1940 brick laid in soft lime mortar needs a lime-based mix, which is why it lives on our historic masonry restoration page. And a stack with a failed crown and loose top courses needs chimney repair or a partial rebuild, not fresh joints. White mineral bloom alone is a masonry cleaning and efflorescence job, though it usually tells us which joints are next.

Strictly, tuckpointing is a decorative ribbon of contrasting mortar laid over the joint, and repointing is the structural replacement of failed mortar; in Utah the words are used interchangeably, and so are we.

What the work actually involves

  1. Map the joints. We sound and probe every elevation, mark failed joints, and count spalled or cracked bricks before pricing.
  2. Cut out the old mortar. Joints are ground or raked to at least twice the joint width, usually three-quarters of an inch to one inch, with the blade kept off the brick edges. Chipped arrises mark a rushed repoint.
  3. Replace bad brick. Spalled units are cut out whole and a matched salvage or production brick set in their place.
  4. Clean and dampen. Dust is flushed out, then the brick is wetted so it doesn’t pull water from the new mortar before it cures.
  5. Pack in lifts. Mortar goes in roughly a quarter inch at a time, each layer compacted before the next, so the joint is dense all the way back, not a skin over a void.
  6. Tool and cure. Once thumbprint-hard, the joint is tooled to the original profile, then kept damp and shaded for days; mortar that dries fast in Utah sun cures weak and pale.
Angle grinder throwing sparks, the tool used to cut failed mortar out of brick joints before repointing

Matching mortar to brick that is already there

The mortar must be softer than the brick. The joint is the sacrificial part of the system; when a repoint uses a mix harder than the units around it, the brick takes the stress and its face shears off. Much spalling on older Wasatch Front homes is a well-meant repair with the wrong bag. For most Utah brick from the 1950s onward, Type N mortar is the match; softer older units get Type O or a lime-rich blend, and Type S only where the original work used it.

Color is matched on the sand, not the dye. Mortar is mostly sand, and its color and grain size decide how a joint reads from the curb once it weathers, so we set test panels with local sands before adding pigment. Profile matters as much: concave sheds water best, weathered throws a shadow line, raked looks sharp and holds water. The Wasatch Front’s 100-plus freeze–thaw days a year punish any joint that cups water, so on exposed parapets and chimney stacks we’ll recommend concave even where the original was raked.

Timing follows the thermometer: mortar needs the wall and air above roughly 40°F for its first days, so late March through early November is the honest repointing season in the valleys.

What does tuckpointing cost in Utah?

As a planning number, repointing along the Wasatch Front typically runs $8 to $25 per square foot of wall, with spot repairs on one elevation often landing between a few hundred and a few thousand dollars. Ballpark ranges, not quotes; a firm estimate follows a site walk and a joint count.

  • Height and access. Gables and chimney stacks need scaffolding or a lift and cost more per foot than a garden wall.
  • Hardness of the old mortar. Portland-heavy 1970s joints grind slowly; soft old joints rake out fast.
  • Brick replacement count. Each spalled unit is its own small job, and discontinued brick can mean a salvage search.
  • Spot versus full elevation. Patching the worst joints is cheaper now; a whole weathered face blends better and costs less per joint.

Our B100 license (#14282236-5501) is verifiable at dopl.utah.gov. This work sits inside our wider masonry and site, structure & envelope scopes for when joints are only part of the problem.

Two-story brick house with crews working at the roofline, where parapet and chimney joints weather first

Questions we actually get

How deep do you cut out the old mortar before repointing?

At least twice the joint width, which on a standard three-eighths-inch joint means three-quarters of an inch minimum, and we generally go to a full inch. Shallower than that, the new mortar has nothing to key into and separates within a couple of freeze–thaw seasons. If the old mortar is loose deeper, we keep going to sound material.

Will the new joints match the rest of the house?

Closely, and better with time. We match sand color and grain first, then joint profile, then pigment only if still needed, and set a test panel somewhere inconspicuous. Fresh mortar reads a shade dark; a season of high-elevation Utah sun settles it toward the surrounding joints.

Can my brick be repointed if the cracks run through the bricks themselves?

Not until we know why. Stair-step cracks passing through brick usually mean footing movement, common on Utah County clay and bench soils, and repointing over active movement wastes the money. We look at the foundation first; if the movement is old and stable, joints and cracked units get repaired in one visit.

Does repointing stop water from getting into the wall?

It closes the main path, not the only one. Missing flashing at window heads, a cracked chimney crown, blocked weeps, or a sidewalk graded toward the wall will keep feeding moisture behind the brick. We note those during the joint survey, and route anything bigger through waterproofing and moisture management.

Tell us what you’re working on

We reply within a couple of hours during business hours, a day at most. You’ll get a straight read on what your brick needs and a budget range before anyone commits to anything.

Request an estimate   (385) 236-1741