Interior window & door trim in Utah County
Window and door trim is the casing, stool, apron, and extension-jamb package that turns a bare or drywall-wrapped opening into a finished one — picture-frame, craftsman flat stock, or a traditional stool-and-apron sill. Grandview Contractors installs it on new openings, replacement windows, and builder-grade drywall returns across Utah County and Salt Lake County under a Utah DOPL B100 general contractor license.

When window and door trim is its own job
If every opening just needs its thin casing swapped alongside new base, that lives on baseboard and casing installation. This page is for openings that need more than that: drywall-returned builder windows with no wood on them at all; replacement windows whose frames sit short of the drywall; 2×6 walls that need extension jambs first; or a style change — a stool and apron, a craftsman head, plinth blocks at the doors.
Ceiling-line molding is crown molding, the stairwell is stair trim and skirtboards, and a fogged or failed unit is a replacement through windows and doors before we trim it. All of it rolls up to trim and millwork, usually as the finish stage of a larger renovation.
Three ways to trim a window, and what each asks of the opening
Picture-frame. Four pieces of casing mitered at the corners, with casing standing in for the sill. It’s the cleanest read for modern homes and the usual answer for a drywall-return conversion. It also hides nothing — more on that in the questions below.
Stool and apron. The traditional sill — a stool projecting past the casing with horns notched around the return, and an apron beneath. The stool is the hardest piece in the package — scribed on three sides, first to telegraph a sloppy fit.
Craftsman flat stock. Square-edged legs under a wider head, often with a parting bead and cap, all butt-jointed. No miters to open, so it forgives a slightly out-of-square replacement window, and it suits central Provo bungalows and Vineyard’s modern-farmhouse builds equally well.
Doors follow the same logic: legs meet a mitered or butt-jointed head, a back band adds depth without a wider board, and a plinth block gives tall baseboard a clean place to stop at each door leg.

How we trim a window or door opening
- Survey every opening individually. Jamb depth against the wall plane, square across the diagonals, and whether a drywall return hides a frame we can fasten to. Wasatch Front exterior walls are framed with 2×6 studs for insulation, so a stock 4 9/16-inch jamb rarely reaches the drywall — the gap is measured per opening, never assumed.
- Extension jambs, ripped to fit. Glued and pinned to the frame, set flush or a hair proud of the drywall so casing seats on wood, not a hump of joint compound.
- Stool first, if there is one. Horns laid out, back edge scribed to the frame, ends scribed to the returns, fastened into the rough sill before any casing goes on.
- Casing at a consistent reveal. Legs and head set to a 3/16-inch reveal — the same number on every opening in the house. Miters glued and pinned through the joint; craftsman heads glued to the legs and fastened into framing.
- Apron, back band, plinths. Last on, with returned ends wherever a profile would otherwise show end grain.
- Fill, caulk, hand off. A clean handoff to interior painting — or your painter. Good work should not require detective work.
Two material notes specific to stools. Utah’s furnace-dried January air shrinks a solid stool across its width, and a stool sits unsupported on three sides — so stain-grade stools acclimate in the room before cutting, and paint-grade stools are poplar or MDF, not finger-jointed pine. And a south- or west-facing stool at Wasatch Front elevation takes serious UV; a clear-stained one lightens faster than the casing beside it. Choose the species knowing that.
What window and door trim costs in Utah
Openings are priced per unit, not by the foot — the work is in the fitting. As a planning ballpark, not a quote, a paint-grade MDF picture-frame window in Utah County typically lands in the $150–$300 range installed; add extension jambs, a stool, and an apron and it runs $250–$450. An interior door cased on both faces falls in a similar band. Stain-grade hardwood roughly doubles material cost and adds finishing labor.
The levers are depth, squareness, and count. An insert replacement window — the in-frame method the U.S. Department of Energy describes in its window replacement guidance — almost always leaves a depth mismatch we make up with extension jambs. Twenty square openings in a Lehi tract home install fast; a 1920s house where every window differs does not. You’ll get a budget range at consultation, then an estimate, then a fixed proposal. Our B100 license is verifiable at dopl.utah.gov.

Questions we actually get
Can you add wood trim to windows that are currently drywall-wrapped?
Yes — it’s one of the most common requests from owners of newer homes. We cut the return back to the window frame, add extension jambs out to the wall plane, and trim over that. Loose corner bead or a damaged return is drywall repair we handle in the same visit.
Do I need extension jambs after replacement windows?
Usually. Insert replacement windows sit inside the old frame, which leaves the new frame a quarter inch to over an inch short of the drywall. Casing can’t bridge that gap without a hollow behind it, so we rip extension jambs to each opening’s measured depth and fasten them to the frame first.
Should the window trim match the door casing?
The casing profile should match throughout a floor so the house reads as one decision. Windows can carry more than doors — a stool and apron, or a wider head — because they’re seen from the middle of the room; doors are seen in passing. We’ll mock up one of each in your light before the order goes in.
Why can a picture-frame window cost more than it looks?
Because it hides nothing. Four miters only close when the jambs are square and flush with the wall, so an out-of-square replacement window or a wavy drywall return gets corrected first — shimming, extension jambs, planing a proud jamb. Craftsman butt joints absorb the same problems with less labor, so they often price lower.
Tell us what you’re working on
We reply within a couple of hours during business hours — a day at most. You’ll get a straight read on scope, sequence, and budget before anyone commits to anything.