Commercial Tile Installation in Salt Lake City
Commercial tile installation is tile set in lobbies, restrooms, restaurant kitchens, and retail floors to a spec covering slip resistance, movement joints, and health-code details a home never needs. Grandview Contractors installs it across Salt Lake County and Utah County under a Utah DOPL B100 general contractor license, sequenced to a lease or opening date.

When a tile job is commercial, not just large
Square footage isn’t what makes tile commercial. A 400-square-foot restaurant restroom is a commercial scope; a 1,200-square-foot basement floor isn’t. The difference is who inspects it and who walks on it. Kitchens answer to the county health department; lobbies take a few hundred pairs of wet shoes every January. Those set requirements that ordinary ceramic and porcelain floor tile work doesn’t carry.
This page fits tile inside a tenant improvement, a restaurant build-out, or a commercial renovation of an occupied building — one trade within our broader renovation and build-out work, held to the same standard as every other tile and stone installation we do. For a lobby in 36-inch porcelain panels, see large-format tile for flatness and lippage. If the tile is already down and the joints are failing, start with grout repair and regrouting — most commercial tile complaints are grout and caulk problems.
What commercial tile work actually involves
Four things separate a commercial tile spec from a residential one.
Slip resistance on the record. Floor tile in level interior areas expected to get wet — restrooms, kitchens, entry vestibules — should carry a wet dynamic coefficient of friction (DCOF) of 0.42 or higher under the ANSI A326.3 test. We get the manufacturer’s DCOF sheet before ordering. Polished porcelain that looks right in a lobby rendering often fails this number.
Movement joints, planned, not improvised. Commercial floors need soft joints at perimeters, over slab control joints, and roughly every 8 to 12 feet across the field — tighter in sunlit storefronts. Salt Lake and Utah County tenant slabs move with expansive clay and collapsible bench soils, so we align tile joints to the slab’s joints and run crack-isolation membrane where it has already moved.
Grout and base chosen for the inspector. Kitchens and back-of-house get quarry tile or unglazed porcelain with epoxy grout, which doesn’t absorb grease or acidic cleaners. Restrooms and prep areas get a sanitary cove base — tile that curves into the wall instead of meeting it at a sharp corner — because health departments want a corner a mop can reach. Wasatch Front hard water scales cement grout fast in a restroom cleaned daily — another argument for epoxy.
Transitions that pass accessibility review. Where tile meets carpet or polished concrete in a public corridor, the height change stays under a quarter inch, or beveled up to a half inch, under the ADA Standards for Accessible Design. In restroom retrofits we hold tile build-up so fixture clearances survive — a thick mortar bed can quietly erase an inch the plans needed.

How a commercial tile scope runs
- Submittals first. Tile, setting materials, grout, and membrane go to the architect or landlord as one package with DCOF data. Downtown Salt Lake landlords often add finish standards of their own.
- Slab and schedule check. Moisture test, control-joint map, flatness check for the tile size. Tile then sits in the critical path: after plumbing rough-in and drywall, before casework, cured before the health inspection.
- Prep and membranes. Self-leveling, crack-isolation over suspect joints, and waterproofing pitched to drains wherever a room gets hosed or mopped.
- Set, grout, protect. Cove base before wall tile, soft joints filled with sealant, epoxy grout placed in sections so it stays workable. Finished floors get hardboard protection because the trades behind us roll carts.
- Closeout. Attic stock boxed and labeled, maintenance guidance for the cleaning contractor, DCOF and material data left with the owner.
Floor drains, trap primers, and wall-hung fixture carriers are plumbing work. Grandview holds the contract and manages the licensed plumbers who do it; we coordinate, sequence, and quality-check their rough-in before tile goes over it. Our B100 license is verifiable at dopl.utah.gov, which landlords tend to check before approving a tenant improvement.
What moves commercial tile cost in Salt Lake City
As ballpark planning numbers, not a quote: commercial porcelain floor tile in the Salt Lake market usually lands between $12 and $30 per square foot installed, including setting materials and membranes. Quarry tile with epoxy grout and cove base in a kitchen runs higher per foot than the dining room. A real number follows a real scope and a site visit.
- Working hours. Tile in an occupied building often happens after hours or in phases to keep a storefront open. Both add labor and calendar days.
- Entry conditions. Vestibule tile on the Wasatch Front takes roughly 100 or more freeze-thaw days a year tracked in on boots and salt. Frost-rated porcelain, a recessed walk-off mat frame, and exterior-grade setting materials cost more than interior-only product.
- Slab condition. Older Salt Lake buildings and fast-growth tenant shells in Lehi and Saratoga Springs fail flatness for different reasons; either way, self-leveling is the line item that appears after demo.

Questions we actually get
Can you tile our restaurant while we stay open?
Usually, in phases. We split the floor behind temporary barriers, work nights or closed days, and keep a path to restrooms and kitchen open. Rapid-set mortar shortens cure windows but doesn’t erase them, so each phase needs a day or two before it takes carts.
What does the health department look for in restroom and kitchen tile?
Smooth, non-absorbent, cleanable surfaces: sealed or epoxy grout, a coved base at the floor-to-wall joint, floors pitched to drains, no open cracks or missing grout. Requirements vary by county and use, so verify specifics with the Salt Lake County or Utah County health department before finishes are ordered.
Why does commercial tile cost more per square foot than tile in a house?
Heavier-bodied tile rated for traffic, epoxy grout, cove base, documented slip ratings, more movement joints, and working around a tenant’s hours. The tile is often cheaper per box than residential marble; the assembly and schedule around it cost more.
Our lobby floor cracked in a straight line. Is the tile defective?
Almost never. A straight crack through tile usually traces a slab control joint or shrinkage crack underneath that the assembly bridged without a soft joint or membrane. The fix is a movement joint cut on that line and the affected tiles replaced over membrane, not a new floor.
Tell us what you’re working on
We reply within a couple of hours during business hours — a day at most. You’ll get a straight read on scope, sequence, and budget before anyone commits to anything.