Vinyl picket fences in Utah County
A vinyl picket fence is a three- or four-foot front-yard fence built from routed PVC posts, rails, and pickets — the classic picket silhouette with no paint schedule, ever. Grandview installs them across Utah County and Salt Lake County under a B100 general contractor license, posts set below frost depth and rails left room to move with the seasons.

When vinyl picket is the right fence — and when it isn’t
Choose vinyl picket when you want a low, open front-yard fence that defines the lot, keeps a toddler or small dog off the sidewalk, and looks the same in year twelve as on install day. It’s the fence HOAs in Lehi, Saratoga Springs, and Eagle Mountain pre-approve most often, because the profiles are standardized and the color never drifts from the approved swatch.
If you’d rather paint than buy maintenance-free — or you want a custom picket top or a stain instead of white — a wood picket fence is the better fit. If the job is screening a backyard, you’ve outgrown pickets; that’s a vinyl privacy fence. For a long frontage on acreage where pickets would look busy and cost too much per foot, vinyl ranch rail gives you the same no-paint material in a two- or three-rail profile.
Vinyl picket is not a security fence and not a wind screen. It’s a boundary you can see through, which is exactly why cities allow it in front yards where a six-foot solid fence would never pass. Like everything on our fencing page and across our site, structure & envelope work, it’s built under one license you can verify at dopl.utah.gov.
What goes into a vinyl picket fence that stays straight and white
Vinyl fencing is an assembly, not a stack of boards. Posts are hollow 4×4 or 5×5 PVC sleeves, routed at the factory so the rails slide into them. Rails are 2×3½ hollow sections with picket holes punched on a fixed spacing — typically ⅞×3 flat pickets or 1½-inch square pickets on 2- to 3½-inch gaps. Pickets drop through the top rail and seat in the bottom; caps finish pickets and posts. Nothing is nailed.
Two consequences follow. Vinyl grows and shrinks with temperature — a Utah County front yard swings from single digits in January to triple digits in July — so rails get expansion room inside the post pockets. A rail screwed hard at both ends bows in summer and cracks in winter. And picket sections rack only a few inches over an eight-foot span, so a sloped lot gets stepped panels or a rackable system ordered on purpose.
Material grade matters. We specify a co-extruded UV-inhibited cap layer, because elevation UV along the Wasatch Front chalks and yellows thin bargain vinyl within a few seasons, plus aluminum stiffeners in bottom rails on spans over six feet and under any gate. We prefer virgin PVC over recycled-core product — recycled vinyl turns brittle fastest in a January cold snap.
How a vinyl picket fence install runs
- Confirm the line and the rules. We locate pins or recommend a survey, call utility locates, and check your city’s front-yard height limit and corner-lot sight triangle — most Utah County cities cap front-yard fences at three or four feet. The HOA submittal goes in with the exact profile and color.
- Lay out posts to the panel module. Picket sections come in fixed six- or eight-foot lengths, so post spacing is set from the panel and corners are solved first. Cut-down sections land next to gates or in the run’s least visible spot.
- Set posts below frost depth. Holes go to 30 inches or more, deeper for gate posts, each PVC post set in concrete and plumbed both ways. On the expansive clay of valley-floor lots, a bell-bottomed footing resists the frost heave that lifts shallow posts a little further each winter.
- Assemble rails and pickets. Rails slide into the routed posts with their expansion gap, pickets drop through and lock, and we check the top line panel by panel so stepped sections read as a clean stair, not a sawtooth.
- Hang the gate and cap everything. A vinyl picket walk gate gets an internal aluminum frame and the gate posts get a metal insert, because a hollow vinyl post alone sags under a swinging gate within a year. Caps go on with vinyl adhesive, and we walk the run with you.

What does a vinyl picket fence cost in Utah County?
As a ballpark planning number — not a quote — installed vinyl picket fencing along the Wasatch Front typically runs about $25–$45 per linear foot for a three- or four-foot fence, gates priced separately. That’s usually a little more than painted wood picket on day one and less over ten years, since there’s no paint or picket replacement in the budget.
What moves the number: profile and color (white flat pickets are the base; tan, clay, and gray cost more, and French gothic or scalloped tops add material), height, corners and gates, stepped panels on a slope, rail stiffeners, and whether an old fence has to come out first — a leaning one is a repair-or-replace call we make on the same site walk. We give a budget range after a site walk and a firm estimate once profile and layout are settled.

Questions we actually get
Will a white vinyl picket fence yellow in the Utah sun?
Quality vinyl with a co-extruded, UV-inhibited cap holds its white for decades; it’s the thin economy product that chalks and yellows. Elevation makes UV here harder on exteriors than at sea level, which is why we specify by cap layer, not by price.
Can vinyl picket fencing follow a sloped front yard?
Yes, two ways. Standard picket panels rack only a few inches per section, so most slopes get stepped panels with a level top on each one. For a continuous top line on a steady grade, we order a rackable picket system up front. The choice is made at layout, because it changes post spacing and rail counts.
Does a vinyl picket fence hold up to a Utah winter?
Good vinyl does, if two things are right: posts below frost depth in proper footings so heave can’t tilt them, and expansion room in the post pockets so winter contraction doesn’t crack the rails. We avoid installing during hard freezes, since cold vinyl is brittle and doesn’t take a rubber mallet kindly.
Can you match my HOA’s approved vinyl fence profile?
Usually, yes. Most Utah County HOAs reference a specific profile, height, and color code, and we build the submittal around exactly that. Where the named profile has been discontinued, we propose the current equivalent and document it so the committee can approve in one pass.
Tell us what you’re working on
Send us the rough footage, your HOA’s fence guidelines if you have them, and a photo of the frontage. We reply within a couple of hours during business hours — a day at most — with a straight read on profile, layout, and budget.