Renovation & Build-Outs · Interior Painting

Cabinet painting & refinishing in Utah County

Cabinet painting takes kitchen and bath cabinets down to degreased, scuffed wood and rebuilds the finish with a bonding primer and a sprayed, hard-curing enamel — doors finished flat off-site, frames in place. It’s the right move when the boxes are sound and only the look is dated, and Grandview Contractors does it across Utah County under a Utah DOPL B100 general contractor license.

Discuss a project   Or call (385) 236-1741

Kitchen with freshly refinished blue painted cabinets and white countertops
Who this is for

When painting beats refacing or replacing

Paint the cabinets you have when the boxes are plywood or furniture-grade MDF, the doors hang square, the glides still run, and the only complaint is the honey oak. That describes most Wasatch Front kitchens from the 1990s and 2000s, and the flat-panel maple in newer Lehi, Saratoga Springs, and Eagle Mountain subdivisions. Those cabinets were built to last. Their color was not.

Don’t paint cabinets that are failing. Particleboard swelling under the sink, thermofoil peeling at the edges, a warped door, or a layout you dislike — those are jobs for cabinet refacing (new doors and veneer over the existing boxes) or cabinet replacement inside a kitchen remodel. Paint fixes finish, not structure, and we’ll tell you which one you’re looking at on the first visit.

Trim and door painting uses the same enamel family but runs in place, without the degrease-and-pull sequence cabinets need. Single-room painting covers the kitchen walls — a common pairing, scheduled after the frames cure.

Process

What cabinet refinishing actually involves

  1. Label and pull. Every door, drawer front, and hinge gets a numbered tag that follows it to the shop and back. Hardware is bagged by cabinet.
  2. Degrease. Cabinets carry years of cooking and hand oils, heaviest above the range and beside the sink. We wash, rinse, and dry. Skip this and the best enamel peels in a season — the most common reason DIY cabinet paint fails.
  3. Fill and sand. Old hardware holes are filled if the pulls are changing; oak gets grain filler if you want a smooth look. Everything is scuff-sanded, vacuumed, and tack-wiped.
  4. Prime for the species. Stained oak, cherry, and some maple bleed tannins through ordinary primer and leave pink or yellow ghosts in a white finish; those get a shellac-based stain-blocking primer. Laminate gets a bonding primer rated for slick substrates.
  5. Spray. Doors and drawer fronts are sprayed flat on racks, both faces, two coats of waterborne alkyd or two-part urethane enamel. Frames and end panels are masked, tented, vented, and sprayed in place. Utah’s dry air flashes waterborne finishes fast, so we adjust product and conditions rather than fight orange peel afterward.
  6. Cure and re-hang. Enamel won’t cure properly below roughly 50°F, so from November through March doors cure in heated space, not a garage. Hinges go back on their original holes, doors get adjusted, new hardware is bored with a jig, and we leave labeled touch-up paint behind.
Power drill, hinge bracket, and gloves staged for re-hanging refinished cabinet doors
Materials

Why the finish system matters more than the color

Wall paint on a cabinet door stays soft, sticks where door meets frame, and chips at the edges within a year. Cabinet work uses coatings that cure hard: waterborne alkyd enamels for most kitchens, two-part catalyzed urethanes where you want the closest thing to a factory finish. Both level out under a spray gun as no brush can.

Color behaves differently at elevation. South- and west-facing kitchens in Utah take intense high-elevation UV through the windows, and oil-based enamels amber visibly on the sunny side within a few years. Waterborne systems stay truer, which is why we default to them for whites.

One check before sanding starts: age. Cabinets in pre-1978 homes across older Provo, Orem, and Salt Lake City neighborhoods may carry lead-based coatings under later layers. We test first, and a positive result means the prep follows EPA lead-safe renovation practice — contained, wet-sanded, HEPA-cleaned — rather than dry-sanding dust into a room where people eat.

Bright kitchen with smooth white painted cabinets and wood floor after refinishing
Budget

What does cabinet painting cost in Utah County?

A typical Utah County kitchen with 25 to 35 doors and drawer fronts lands roughly between $4,000 and $9,000; a bathroom vanity runs a few hundred to around a thousand. Those are ballpark planning numbers, not a quote — the estimate follows a piece count and a look at the existing finish, in writing.

What moves the number: piece count (cabinets are priced per door, not per square foot), grain filling on oak, a dark-to-white change that needs a third coat, hardware changes that mean filling and re-boring, glass-front doors, and islands with decorative end panels. Refacing commonly runs one and a half to two times the cost of painting, and new cabinets several times that — which is why painting is the first thing we price when the boxes are good.

Questions we actually get

Will painted cabinets chip?

Any finish chips if a cast-iron pan hits it. The difference is daily wear: a degreased, primed, sprayed enamel takes years of hands, dishwasher steam, and cleaning without flaking at the edges, while wall paint over an unwashed door fails within months. Expect to use the touch-up paint a few times a decade.

Can you paint oak cabinets so the grain doesn’t show?

Yes, with grain filler — a skim-and-sand step repeated once or twice per door before priming. It adds real labor, so it’s a line item; plenty of clients keep a faint grain texture and spend the money on hardware instead. We’ll show you both on a sample door.

How long is the kitchen out of commission?

Mostly it isn’t. Frames are prepped and sprayed on site over two to three days, during which the kitchen is tented and you’ll want a couple of dinners out. Doors and drawer fronts are away for roughly a week to ten days; in between, the cabinets work open-shelf style.

Can thermofoil or laminate cabinets be painted?

Intact laminate can, with a bonding primer rated for slick surfaces and the same enamel system. Thermofoil that’s peeling or bubbling — common beside ovens and dishwashers — can’t be fixed with paint, because the film is letting go of the MDF underneath. Those doors are refacing candidates, and we’ll flag them on the walk-through.

Related services

Cabinet refinishing is one scope within our interior painting work, part of the renovation and build-out family. If the boxes aren’t worth painting, cabinetry and countertops covers refacing and new installation, and a kitchen remodel is the path when the layout is the problem. Many clients pair cabinets with a whole-home repaint before a sale. Our license is verifiable at dopl.utah.gov.

Tell us what you’re working on

We reply within a couple of hours during business hours — a day at most. You’ll get a straight read on scope, sequence, and budget before anyone commits to anything.

Request an estimate   (385) 236-1741