Renovation & Build-Outs · Drywall

Drywall Texture: Knockdown, Orange Peel & More in Utah County

Drywall texture is the sprayed or hand-applied coat of joint compound that gives walls and ceilings their surface pattern — orange peel, knockdown, skip trowel, and the hand textures in between. Grandview Contractors applies new texture and matches existing texture across Utah County and Salt Lake County under a Utah DOPL B100 general contractor license, from one patched ceiling to every wall in the house.

Discuss a project   Or call (385) 236-1741

Roller and tray of white primer staged on a work table before texturing drywall in a Utah County home
Choosing a pattern

Orange peel, knockdown, or hand texture — and when texture is the wrong answer

Orange peel is a fine splatter sprayed through a hopper gun and left to dry. It’s the most forgiving pattern, the easiest to match on a repair, and the texture on most Wasatch Front homes built since the 1990s. It suits basements, garages, and rentals, because small dings vanish into the pattern.

Knockdown starts as a heavier splatter, then gets flattened with a wide knife once it begins to set. The result is a mottled, low-relief surface that reads calmer than orange peel and hides joints better than smooth. It’s the default on main-floor rooms in a lot of Utah County subdivisions from the 2000s, and the one homeowners most often ask us to match after a patch.

Skip trowel, Santa Fe, and swirl go on by hand with a trowel or brush. They’re slower, cost more, and show the finisher’s hand — which is the point on custom and older homes.

Texture is not always the answer. Walls with no pattern at all are a Level 5 smooth finish. Erasing a dated pattern is skim coating. A hole or crack is a drywall repair with matching folded in, and on new board texture is the last step of a drywall installation. This page is for when the texture itself is the decision.

How it’s done

How texture gets applied — and matched

  1. Finish the board properly first. The Gypsum Association’s levels-of-finish standard allows heavy textures over a Level 3 finish and puts light textures like orange peel over Level 4. We finish to Level 4 under either, because texture hides less than people hope once evening light rakes across a wall.
  2. Prime before texturing on new board. Bare paper and dried compound pull moisture out of wet texture at different rates, so the pattern reads coarser over paper than over joints. A coat of drywall primer evens the suction so the pattern is the same corner to corner.
  3. Mix to the pattern and shoot a test board. Orange peel wants thinner mud and a smaller nozzle; knockdown wants heavier mud, a larger nozzle, and lower pressure. A sprayed scrap gets checked under raking light against your existing wall or chosen sample.
  4. Spray in overlapping passes, ceilings first. Distance and speed stay constant, because every change shows up as a band. Floors, cabinets, and windows get masked before the compressor starts.
  5. Knock it down on time. The splatter has to lose its wet sheen before the knife touches it — too early smears, too late scratches. In Wasatch Front air that window is short, often ten minutes on a summer afternoon, so we work one wall at a time rather than spraying the whole room first.
  6. Prime and paint wall to wall. Fresh texture takes primer, then paint across the entire wall, not just the patched area. Paint sheen gives away a patch long after the texture itself is a perfect match.
Two finishers rolling primer across a freshly textured drywall wall before paint in a Utah renovation

Matching an existing pattern means reading the splatter size, the knockdown pressure, and the era. We feather new texture past the patch edge so the transition disappears, then hand the wall to our interior painting crew. On ceilings textured before the early 1980s, we have the material tested for asbestos before anything is scraped — EPA guidance is clear that intact material is safer left alone than disturbed untested.

Budget reality

What drywall texture costs in Utah

Pattern is the first cost driver: sprayed orange peel is fastest, knockdown adds the knife pass, and hand textures take a finisher’s time on every square foot. The second is what’s under it — new texture over fresh board is one step, while re-texturing a wall that already has a pattern usually means a skim coat first. Ceilings cost more than walls for the same area, and a furnished home needs more masking; overspray does not respect drop cloths that stop a foot short.

As ballpark planning numbers, not a quote: spraying orange peel or knockdown over finished, primed drywall typically lands in the $0.75–$1.75 per square foot range in Utah, with hand textures above that. Matching texture on a single patch is priced as part of the repair visit, not by the foot. Whole-house re-texture is priced room by room once we’ve seen what’s under the old pattern. You can verify our license at dopl.utah.gov before we come look.

Bright finished basement with daylight raking across textured drywall walls in a Utah County home

Texture closes out most of our drywall services and nearly every renovation and build-out we run.

Questions we actually get

Can you match knockdown texture on a repair so it disappears?

Usually, yes. Knockdown is harder to match than orange peel because knife pressure and timing vary by whoever did it originally, so we shoot a test patch and compare it under raking light first. Once matched, we prime and paint the whole wall. If a wall has been patched too many times to blend, we’ll say so and suggest a skim coat instead.

Is orange peel texture outdated?

Dated in the sense that it’s everywhere, not in the sense that it’s wrong. It’s still the most practical texture for basements, garages, and rentals because it hides wear and is cheap to repair. For main-floor rooms, a lighter knockdown or a smooth Level 5 finish reads more current.

Can you spray new texture over the existing texture?

Over orange peel, a heavier knockdown can sometimes go on directly after a good primer, and we’ll tell you if your walls qualify. A lighter pattern over a heavier one doesn’t work; the old texture telegraphs through, so that wall gets skim coated first. We check a test area before quoting either path.

Do the walls need to be primed before texture?

On new board, yes. Unprimed paper and compound absorb water from the texture at different rates, so the pattern comes out finer over joints and coarser over paper, and it shows after paint. Priming first costs a little and avoids re-doing the room. We prime patch areas before matching for the same reason.

Tell us what you’re working on

We reply within a couple of hours during business hours — a day at most. You’ll get a straight read on scope, sequence, and budget before anyone commits to anything.

Request an estimate   (385) 236-1741